Search:

When I first started loading cast in the 45 used the roll crimp as shown in the article. Got out of 45 for a while and when starting back picked up a used set of Hornady dies at a gun show and the...

The RN like the 311291 feed fine in my 03A3 and in a pre-64 M70 I used to own. The 311041 with the flat point would hang up in the extractor cut on both. The drawing for the 31-194 looks similar to...

Have used SWC with speed loaders and sometimes the shoulder on the bullet will hang up on the edge of the chamber and slow the reloading process. RN and TC bullets will slide right in making for a...

Bought some several years ago and have just started to use it in my Rem 513T. At least 1/3 will not allow the bolt to close, about half close but require a good bit of effort and the rest seem okay....

Timely post, in the process of replacing my electric range. Gas is not an option so sticking with electric. One thing I noticed that if you think of the standard four burner with one large burner...

Moved 16 times with the Army including twice to Germany. Moved again by myself from WI to KY and hired movers. Downsized a lot for the last move and brought my guns and reloading and casting stuff...

The threads on my used LAM I stripped and sent it to RCBS for repair. They sent me a new LAM II as a replacement at no charge. Clean the internal threads before installing a new die, makes it...

Found another floater this AM but cause of death was obvious, the last 1/3 of what had been a 9-10 inch bass was bitten off! Checked the gills and they looked healthy. Don't have any big fish in the...

The bass I found this AM was fresh but didn't think to cut it open. Heck, wouldn't know what I was looking for. From what I could see of the gills they looked fine.

By this afternoon the black...

Any of the above could cause issues but would expect it affect all the fish. There is no run-off other than the grassy slope in my yard and the neighbor and she doesn't apply chemicals of any kind. ...

Have a one acre pond on my property, spring and rain water fed. Every spring I add Cutrine and a pond die to control algae, was done before I bought the place and by me for the last five years. ...

The NRA Firearms Assembly book has instructions and a schematic for the Rem 58. PM me your address and I will copy and mail them to you.

The 2.25 X .25 should work but make sure there is enough length for a nut. Forget the correct name but get the locking nuts that have the nylon insert to keep them from coming loose. The bolts on my...

Having traveled a bit of the world learned early that if the local cuisine tastes good DON'T ASK FOR THE RECIPE. There are some things it's better not to know.

Pachmayr Presentation grips come in a large size for the K frames, might try those.

Had the threads strip on my LAM I that I bought used. Not sure how old it was but pretty sure was a lot newer than yours. RCBS had me send it back and sent me a new LAM II free. Nostalgia is fine...

Looks like that mold started life as a Lee 6 cavity and has been extensively modified.

I'll take #8, Gripper grips. PM sent.

Found a later model left hand for my grandson when he gets bigger. Really accurate. There was someone selling replacement springs that would reduce the trigger pull and think it was Rimfire Central...

Number of posts on various forums about using epoxy to attach the base to the receiver, people reported it worked and held up well.

A bevel on the striker may be all you need to mate to the bevel on the safety. If you have a GI trigger on hand swap it with the commercial trigger and see if it does the same thing. If not the...

Years ago the nut that holds the sizing die on my LAM I stripped and RCBS had me send it back. Before shipping it I stripped all the parts off and sent the body to RCBS. They did not repair it and...

Rem, Peters, WRA all loaded soft point hunting ammo for the Krag. Following WWI most of the Krags were sold off cheap and were commonly used for hunting. Some, like the carbines, were used as is...

The Krag I owned had the same issue. Didn't use the O ring but simply fire formed and then neck sized only. Doing it that way there were no further issues.

My safe is int 500# range and found it was easy to move, called the local movers and they did it. When I moved from WI to KY the moving company moved it. They had me leave the door open and removed...