Be really really sly sneakin' up on the mirror when you shave.
Type: Posts; User: zdogk9
Forum: Reloading Equipment
Be really really sly sneakin' up on the mirror when you shave.
Forum: Muzzleloading.
Get the Lee .501/440 mold for the .50 S&W paper patch it, run it through the Lee .501 sizer put it over 80-90 grains of your favorite and you're good to go. Read the 'Paper Patching for the...
Forum: Black Powder Paper Patching
I think I'm following this OK, one question I have is. What sort of shrinkage can I expect from cavity diameter to finished bullet diameter? Darn it to heck, I thought I had it bad just with my...
Forum: The Star Equipment Corner
You stole it. Now you're gonna have to sneak up on the mirror to shave.
Forum: Hunting with CB's
I'm playing with the same combo at the moment and have been quite pleased with the results I'm getting, only I'm sizing to 0.310, PM me an addy. and I'll sent you 20 or so to play around with.
I just competed a transaction with him, fast, smooth and a good deal all around.
Zdog
Forum: Cast Boolits
I'm super confused now too; I was just going to order a Lyman M die to aid in seating my cast boolits, should I reconsider?
yes, buy it, good to have
Forum: Muzzleloading.
Why, I can get five shots on a playing card at 75 yds. using The lee bullet described by IdahoRon, from a standing position. Are there any style points I'm unaware of here?
Forum: Reloading Equipment
That is a sign that you're going to buy a Smif 57
Forum: Muzzleloading.
Go to your local thrift store and look for felt hats.
Forum: Casting Equipment
The drip just falls through the hole into the sprue can.
http://i18.photobucket.com/albums/b111/bobkelim/PB110136.jpg
Forum: Cast Boolits
I ran a 240 15 amp circuit to my shop for my new Lee twenty pounder, then cast 15# of RCBS 150 gr. SWC and 100 or so 160 grain boolets for my 32 special and paper patched 30 of them.
Forum: Cast Boolits
This is how I do it. Spend a couple of hours with a friend. Make him check EVERY ONE of his re-loads at each step of the process. This teaches him reloading and makes the reloads HIS. be sure to...
Forum: Cast Boolits
This is very expensive fertilizer. The only way you could pay more would be to buy a horse.
Ease the sting by writing what you think of the ex in her lawn with the mixed powder. It'll be hosed off...
Forum: Leverguns
The RCBS mould will cost about as much as three boxes of ammunition. Say two trips to the range if you're taking it easy on the shooting.I figure that I can't afford NOT to buy moulds for every fire...
Forum: Muzzleloading.
without the wad and all else the same I'd rate the load as improved cylinder at best.
Forum: Muzzleloading.
I'm running the Lee .501 440g paper patched and sized back to .501, over powder wads cut with a hole punch and dipped in 50% bees wax 40% crisco and 10% extra virgin olive oil. This over 90 grains of...
Forum: Reloading Equipment
The RCBS dies can be fiddly in the L&LAP I've found that if I play with the indexing pawls I can eliminate the problem with 10mm and .45 ACP which are what I reload on this machine. I'm told that a...
Forum: Cast Boolits
Bought a 311041, about two months ago. It casts very well, the sprue plate had to be sharpened however. The cutting edge was a proud 1/32" flat or skinny 1/16" which made it impossible to get a good...
Forum: Cast Boolits
I just got a lyman 2cavity. what I'm encountering is the sprue not dropping off of the cutter plate without beating on the mold handles. It looks as if the edges of the holes have about a 1/32+ flat...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |