that site does not look like the Starline site i use. starlinebrass.com as a large banner at the top warning of scam sites.
Type: Posts; User: jj850
Forum: Reloading Equipment
that site does not look like the Starline site i use. starlinebrass.com as a large banner at the top warning of scam sites.
My DL-105 has MEC bottles on it they work ok but they are not quite right. I think I will check out some spray bottles next time I Get a chance.
thanks for the idea Ausglock. Never even thought...
Forum: Reloading Equipment
I think Forester will lap the neck of their die to any size you want.
Forum: Military Rifles
I feel like this should in purple Ok sorry how do I make my comment purple?
Forum: Single Shot Guns
S&W bought TC for there equipment, especially Barrel making equipment , And drove the rest of the company in to the ground through neglect.
Forum: Our Town
Is anyone else getting legal notices for the Remington bankruptcy or just me. How do I find out why I am on their list.
Kind of makes you wonder how much has changed. Colt1873 (don't drop it) Sig Pxxx (don't drop it)
Forum: Cast Boolits
The book looks like an older hornaday manual. The sheet taped to the page I have not seen before.
Forum: Our Town
Riley's bar and grill in Iola Kansas. or the cattlemen's club in battle mountain Nevada. Both had a good ribeye twenty or so years ago. If you asked for rare at the cattlemen's club you better want...
Forum: Our Town
you don't need two scales to start. Either will work for powder but the lyman has capacity to weigh bullets or loaded cartridges and digital is easier to use if you keep it calibrated and zeroed....
Forum: Our Town
Have one in a box in the basement right now. Got most of it could not get the spring down the side of the hammer . Sometimes it is better to just walk away for awhile.
Forum: Our Town
I am learning lo listen when that voice in my head says (this is going to hurt ) .IT has taken far too long however
Forum: Our Town
help me if I am thinking about this wrong, but if the round is in front of the extractor how will the firing pin reach it
Forum: Reloading Equipment
you may have to use an expander die and mandrel after you trim , before you turn. to make the neck fit the mandrel
Forum: Our Town
I had a similar problem with a newer F750 and a cummins engine. Every things fine until you had to pull a hill. In my case it was the fan clutch.
Forum: Case Forming / Re-forming
I used COW and I think red dot to form 6mm Ackley with no problem I started small with the powder charge and increased until I got a case formed to about 70 -80 percent . If you do in the back yard...
Forum: Our Town
I read on this site a year or two ago. If you can see the hole cover it with a clear glass bowl. the hive will overheat and suffocate. As long as they can see outside they wont dig under or another...
Forum: Our Town
anyone know how this is different from the Marshall and Sanow research. As I remember it was mostly police shootings with handguns. it became controversial for data analysis, selection bias and...
Forum: Our Town
auto parts store or automotive paint supply store should have adhesive remover for most automotive type decals
Forum: Factory & Surplus Powder
I saw it on the shelf today at sheels.
Forum: Case Forming / Re-forming
It is when you start bringing thicker brass from the shoulder into the base of the neck. Or pushing the larger diameter of the shoulder in to the smaller diameter of the neck, still the same amount...
Forum: Factory & Surplus Powder
here is the article http://bulletin.accurateshooter.com/2016/11/imr-releases-five-new-pistolshotshell-powders/
Forum: Factory & Surplus Powder
An article on accurate shooter said imr is releasing five new powders called red, blue, green, unequal, and target available jan 17
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |