When you manually import the file, it gives you the option of what scale everything should be in. You can manually adjust it down to make it match.
If you just open the file with fusion it does not...
Type: Posts; User: Andar
Forum: 3D PRINTED RELATED ITEMS
When you manually import the file, it gives you the option of what scale everything should be in. You can manually adjust it down to make it match.
If you just open the file with fusion it does not...
Forum: 3D PRINTED RELATED ITEMS
Worst case print everything with a brim so that lifts up instead of the actual part. If it keeps going then tape the brim down too haha.
Clean your bed and check it for divots. Try also lowering...
Forum: 3D PRINTED RELATED ITEMS
Sorry, tested again using the other side of the spring and the 1/4 fits the 7. I guess I mangled it a bit during prototyping.
Forum: 3D PRINTED RELATED ITEMS
1mm except for the 1/2 which is 1.1 mm.
Forum: 3D PRINTED RELATED ITEMS
The 7 doesn't fit.
8 fits the 1/4.
10 fits the 5/16 and the 3/8 but it might go a little loose over time. I can't pull the spring out, so it's good.
13 fits the 1/2 but is a little tight. That...
Forum: 3D PRINTED RELATED ITEMS
Printing now. Will be done in 2.5 hours, but unknown if I can confirm fitment before around 10pm or so.
Files looked the same by the way.
Forum: 3D PRINTED RELATED ITEMS
Yup, just downloaded it. Haven't grabbed a new version since 1.2.0
Modification date for #13 is "December 23, 2020, 9:55:30 PM" if you're worried.
Forum: 3D PRINTED RELATED ITEMS
TylerR, the files I'm testing are Spring_Adapter_x_DT (7,8,10,13) right?
Just about to slice and print.
Forum: 3D PRINTED RELATED ITEMS
Will do, just need to wait for the little one to go for a nap so I can get everything sliced up.
Forum: 3D PRINTED RELATED ITEMS
Haha, good catch! I made those and I didn't check that part. Looks like my chart and his had the columns in a different order and the data just got copy-pasted over.
Forum: 3D PRINTED RELATED ITEMS
Filament Brand: Hatchbox
Filament type: PLA
Filament colour: Blue (Sometimes it says true blue)
bed temp: 50 Glass bed, 60 with stock Magnetic sheet
nozzle temp: 200
hot end type: Stock
printer...
Forum: 3D PRINTED RELATED ITEMS
Ammo Mike is my bullet feeder, TylerR is my case feeder. Both using the jgy370 motors so the increased size works better for the lighter cases.
273346
Forum: 3D PRINTED RELATED ITEMS
It's looking great, amazing job dude. I'll take another look at it tomorrow.
Forum: 3D PRINTED RELATED ITEMS
I added a simpler picture of the wiring to the album, your choice if you want to change it with later revisions.
Sorry for not including it right away.
Forum: 3D PRINTED RELATED ITEMS
Looks like it's still the old manual, acknowledge page still has both typos.
Forum: 3D PRINTED RELATED ITEMS
No, it's spelled wrong. miLe instead of miKe.
Forum: 3D PRINTED RELATED ITEMS
This is going to make me seem terrible, but who cares. Due to AmmoMike, you and the rest of you guys, I got back into reloading. I bought my press 4 years ago, loaded 20-30 rounds and stopped using...
Forum: 3D PRINTED RELATED ITEMS
Awesome work! Already reading and adding suggestions.
Forum: 3D PRINTED RELATED ITEMS
Here's what mine looks like so far. Just need to get out and buy the bolts for the mount, hide the wiring a bit then they're good to go!
273193
Forum: 3D PRINTED RELATED ITEMS
Sorry, I can't test that. I don't have their die otherwise I would. I actually printed off this one here and used a 1/2 ID 5/8 OD vinyl tube which fit in the die snug, then a little loose but useable...
Forum: 3D PRINTED RELATED ITEMS
Try it with a small brim and no supports, it shouldn't need any. If you've got a lot of faith in your bed, try without a brim but I'd be using one myself.
Forum: 3D PRINTED RELATED ITEMS
A 4mm brim or so should also work depending on your bed, more if it's not sticky enough, rafts make things ugly and waste a lot. I only use them when I need to avoid "elephants foot" or the sagging...
Forum: 3D PRINTED RELATED ITEMS
You should print out a calibration cube and double check what actually happens. Your X and Y axis should be bang on 20mm for example, but your Z axis should be slightly shorter based on your layer...
Forum: 3D PRINTED RELATED ITEMS
Check your "Raft Air Gap". If you're using Cura, you need to open your settings and enable the option, as it's hidden by default. Lower the amount and try out a few things. Other slicers have a...
Forum: 3D PRINTED RELATED ITEMS
Ooof, ouch, that sucks. I printed mine with a brim just to be sure that wouldn't happen, should probably have a note about that.
Might be time to invest in Octoprint and The Spaghetti Detective if...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |