Search:

i own 2 ballsiti-cast mrk 2's and have had the unfortunate pleasure of dealing or i guess trying to deal with NVM or NVballistics but they really suck at everything. i would advise you to not buy...

i use 1 40 S&W case with pistol brass and a 45acp with 223 in the FA tumbler
4-5 2 liter bottle caps full for the cement mixer with ~6k 9mm brass or equivalent amount of other cases

Drying the...

to run a set of 4 you need to remove the empty carrier arms and springs . i have a video of it some where will dig it out for you.

not untill now i did a search for magma and set to sort by date this was on top and every thing else was from today. . . weird.

i have replaced them it is easy they drive out with a hammer and rod. you can check them with a tester for continuity to see if they work if you can get to the harness what mark# pot is it? it might...

Some times when i get lube on the nose of the bullet it is because i push it to far "have the punch set to long" and the second bullet wipes it out leaving stripes of lube. also lube on the nose can...

abuquerqueBullet - If you can upload it to a site like photobucket, you can paste a link of it running that way, that sure sounds like a fancy machine running that fast[/QUOTE]

It is actually very...

The punch is not in the machine in the video i don't remember where i put it i don't use this machine.

http://s1262.photobucket.com/user/ABQBULLET/media/MOV03426_zpsfgctza3w.mp4.html?sort=3&o=0
...

Wounder how much shipping would be all the way to the AU.

Doh non-lubing sizers? how can post a video for me of mine? over 5100 per hour i think it runs at. i am not the most computerable.

it has 2 steams of lead the melting pot has a slit on the bottom going front to back then there is a orifice plate with 2 holes that bolts over the slit the lead can only flow from the holes in the...

I came across a homemade one on youtube. wounder if its a member? it used a pre-melt pot pretty cool. sometimes i wish i didn't have the big machines so i could build more stuff!!
...

Your best bet is the reclaimed lead shot on rotometals 1.24 shipped. The time you will save driving and buying little by little will make up to cost difference.

I am a gearhead so i buy none working machines that owners thought they beat beyond use. and I make them right again. just bought a old working bulletmaster for 1400 and am doing a digital temp and...

the magma pots run hot i like the ballisti-cast pots with the heated valves it can maintain good bullets at 615F using hardball alloy. I run my 300gr at 595 the other day.

what is the lowest temp you have tried and why did you decide on 760 that is very high.

What temperatures are you running? running it to hot will make lead smear under the sprue plate which causes the sprues to stick really bad. the sprue basically welds to the under smear forming a...

below the sheer pin the long arm that goes all of the way back to the motor. on the side below the sheer pin it can be disconnected with it should be a hitch pin and clevis pin. you can tighten or...

if you are flowing lead to soon try turning to knob on the front of the machine the last picture. and read the manual
3rd page
http://www.magmaengineering.com/PDF/Bullet_Master_MK8_Instructions.pdf

I believe the 2 knobs adjust the position of the lead flow switch adjsuting the position will adjust when in drops lead. the wheel looks to be under rotated? the position of the wheel is adjusted by...

Howell started in 89 and Olympic was in the late 70's to late 89 they where located in the same city just a few blocks away and i think it was a bought by Howell. so it IS the predecessor. it is...

They make just such a thing you can tumble onto sticky bullets to un-sticky them . it was called bullet dust back in the day and sold to reduce the lube smear when shipping cast bullets with tumble...

Welcome to the forum.
What part of the world are you in?


I would recommend 2 pots one for refining and one for alloying. You will need to alloy the lead to make good bullets, the fill out will...

He sold it to me. There is no speed control on this one. It has the limit switch tube. and it will out run a lubemaster. its working perfectly for me.

Bought a casting machine and a lot of molds from Powersgt when he shut down hes company and he is very good to deal with.