Search:

I should also add... that there may be a market that exists that is not being addressed by any mold maker.

That is creation of custom/user designed molds for 7mm and under. I know for sure I...

Seems like quite a few people with all the negativity have no clue how a new business is started. I guess ignorance is bliss. Just by the fact the the OP is taking the appropriate steps to put...

Within the GB threads, we were told even though HP pins were the hold up, the non HP molds (both brass and Alum) would not be produced for the group buy until the HP's were ready. Intent being on all...

Just swap it with me and I'll send along a savage 24 in 223/20ga. It's all setup with a scope mount. ;)

But the serious answer is that varmint rifle in 22 mag or 17hmr or 17bmag can be found for...

I didn't know if it matters, but my+handles on number 18 in the 8cav mold list is not bolded. Just thought I'd mention this in the .005% chance it would mean I didn't get handles.

Earlier this year my scrap yard gave me $3/lb for my jackets. I was a very happy shooter.

A Swiss army knife. Farmer pattern. It's all you need for splitting pelvis and sternum. Also I have done it with an opinel no 8 garden knife. It sounds counter intuitive, but splitting the pelvis is...

Mp NATO 73gr is pretty much built for this purpose. I've had good luck with it powder coated and shot from a 1:9 mid length. I had to remove the buffer weights and open the gas port a few thousands ...

Pickup live trap. Put trap in 5 gallon bucket full of water. Enjoy the primers you have saved

Please take me off this one as well

Can you please take me off the list? I'm going to stick with the heavier version. Thanks.

Man, I don't think I've seen a group buy with so many people signed up.

At the range, he sits at the shooting bench the furthest away from people. So he wont get injured and can keep an eye on other people. So he can live longer. He doesn't walk on water, he makes...

For my 2 MP Brass molds...

I first cleaned with warm-hot water and dawn dish soap. Towel dried.

Then I heat cycled them on my hot plate. The first heat cycle will also dry your mold from your...

Is the honcho activitly communicating with Miha on where we are at with number of molds having been signed up for? (47 total) or is this group buy setup for Miha to check this thread and the other...

The sizing package came with a base first sizing ram. If you have a top punch for the bullet you want to size, insert it into the ram and proceed to size bullets base first

I know this isn't...

I got a refund on mine. I heard through the grapevine that he has switched to UPS. So I think based on that and RKJ... things are back up and running.


MaryB....

What did you do/who did you...

One man's trash is another's....

I have the same sav 24 as the OP. Its my favorite rifle. There isn't anything huntable in michigan that it wouldn't work on. Mine uses irons most of the time but...

My first tests are going to be with the rcbs 77gr RN powder coated. Two sizes for the first test, .310 and .312. Just as soon as I can figure out how to accurately and repeatedly measure out 1.8...

Very much appreciated. I like the look of that 31-84H.

Mr outpost75,

Looks like those images have expired, would you mind letting me know what accurate mold numbers/profiles they were?

Thanks

What is an SV? Do you mean SP? (Set Point)
I understand that PV is the process variable (ie the current temp of the alloy as measured by the thermocouple)

Thanks Hatch!

I have a question I have always wondered about my Hatch pid.

I have autotuned and everything is working just fine, but I'm curious... what is the SET button for? If I just arrow up or down the...

Stop all these tempting group buys!

I'll do one. Dimner @ gmail dot com