A friend was no longer using some casting stuff and gave me one heck of a deal
Saeco mold, 4 cavity .309 /150 gr flat point
H & G handles
Star sizing die with top punch for my sizer
3000+ gas...
Type: Posts; User: robertsm53
Forum: Reloading Equipment
A friend was no longer using some casting stuff and gave me one heck of a deal
Saeco mold, 4 cavity .309 /150 gr flat point
H & G handles
Star sizing die with top punch for my sizer
3000+ gas...
Forum: Cast Boolits
Cast up 20 Lbs worth of 500 Gr boolets for the 45-70.
Forum: Cast Boolits
Cast, weighed, sized and gas checked, 350 30cal 200 gr. 150 30cal 220 grain, 200 .45 cal 530 grain and 50 45 cal. 405 grain slugs.
Forum: Cast Boolits
Just cast another batch of the RCBS 405 Gr. 458 Dia. bullets today, and Thank you Sharps4590. This batch dropped out of the mold a lot easier, and just about 1.5 Grs. heavier, with less variance...
Forum: Cast Boolits
Thanks for the responses guys.
This morning I cast up a small pile of .458 / 405 Gr. bullets and just got done weighing them. As expected they all came in heavier than the stated 405 grs, from...
Forum: Cast Boolits
I'm not new to casting and know that a number of variables will affect the final weight of cast slugs. The question I have for you folks is, for accuracy how big a variance in weight is ok? I have...
Forum: Casting Equipment
Thanks for the information on the hoses. I learned to weld with Oxy/Acet years ago and in fact taught it in Tech School for joint service schools at APG Md. for 5 years. That was about 40 years ago,...
Forum: Casting Equipment
Local second hand / junk shop had a 20 lb. plumbers lead pot with furnace and acetylene cylinder with hose. Was asking 70.00. but I was able to get him down to 50.00. I didn't want the tank so I...
Forum: Casting Equipment
I would like to get the info on repair parts /heating element as well. I have 2 of these and one is out of service due to the heating element burned up and the thermostat control burned out. Any...
CED M2, I started with an old one I don't even remember the brand, changed to the CED millinum, and when it became outdated because it would not talk with today's newer and faster computers, My wife...
Forum: Cast Boolits
cast sized and lubed almost 100 RCBS 500 grain .45 cal bullets for the 45-70
Forum: Cast Boolits
loaded up 250 45-70's with some 500 gr Boolets on top of a mild dose of IMR 3031.
Forum: Cast Boolits
Resized /De-Primed and belled the mouth of 400 45-70 cases, and primed about 1/2 of them. Tonight I get to finish priming and stuff then full.
Forum: Cast Boolits
Resized and primed 250 .32 Win Spec cases, reloaded 10 of them with IMR 4198 at .5 grs below the max, to try out today. Then I lubed another couple hundred of the 38-55 slugs for wife's new Sharps...
Forum: Cast Boolits
Cast up 15 lbs of 500 gr .45 slugs, a few hundred .38 cal 195 gr slugs for her 38-55 and a couple hundred .32 cal slugs for her break top revolver and a derringer.
Forum: Cast Boolits
Received 200 pieces of 38/55 new Starline brass, received a set of cowboy dies also in 38/55 and a mold also in 38/55. Got real busy then, casting a few hundred bullets, pan lubing them and finished...
Forum: Cast Boolits
Cleaned guns, cleaned guns, and cleaned guns. Then I finally was able to de-prime / resize some .32 S&W L for my wife's pocket pistol. That little revolver was so gummed up the extractor would not...
Forum: Cast Boolits
de primed, resized, tumbled with SS Pins 60 40/70 SS brass. Its drying now, hope to stuff them full tomorrow for my wife's Rem Rolling Block
Forum: Reloading Equipment
I have 2 of the 650's and never saw this thread before. I for one am glad it was brought up once again. Although I have not had any long term serious problems I did pick up on a couple of tricks...
Forum: Cast Boolits
Today I rigged both my Dillon 650's with the primer catch tube that actually captures the dead primers and sends them to a closed container to avoid the constant mess of loose primers bouncing out...
Forum: Cast Boolits
Cast up a couple hundred .40 cal 400 gr slugs. Need to try lubing and loading at as cast dia now. The last batch I sized to .,408 were terrible, going through the target sideways. Older orig...
Forum: Cast Boolits
cleaned up a bit and actually found the top of the bench! Ain't actually found that is quite a while.
Forum: Cast Boolits
Flux outside, and cast on a bench with window fan in front of me sucking from behind me and blowing directly out the open window
Forum: Cast Boolits
62, and I've been casting for 40 or so years, but learned 90% of what little I do know now in the past few years lurking around on this site. Still have a lot to learn and am trying to participate a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |