Thanks for the heads up , when I get the funds thinking of get some of them to use. Yes for you to say about being a vendor on here then it will be easier to get in contact with him.
Type: Posts; User: trapper9260
Forum: Gas Checks
Thanks for the heads up , when I get the funds thinking of get some of them to use. Yes for you to say about being a vendor on here then it will be easier to get in contact with him.
Go to the farm fleet store and get the cork sheet that you use to make gaskets, I use the 1/8" thick on , I let a friend use my cutters and told him to use the cork I stated because he needed a...
Forum: Leverguns
This is a good tip on use of a fired case to see about the bullet. Thanks
Forum: Leverguns
I have that mold and size it to .310 and works for me .
Forum: Boolit Lube !
I make my own NRA Lube with ATF and make it as soft as I want it to be by how much you put of one thing. You need to test to see how much of it . That is ATF . I use the heater at times but most of...
What I did is buy the gasket hole punches from Snap on Tool , That is all I use and and a life time warrantee . There is a O ring that you can get in any farm fleet store when the one is worn out....
Forum: Boolit Lube !
This is what I done also . Works for me . I got the idea off the internet. I think it was off of this site.
It is best to get the tool that is stated . Some makers of hulls mainly the ones made in Europe have different size primer pockets. Not like the ones made in the US , it is best to measure the pocket...
Forum: Factory Rifles
Not to get off the subject on pistol round , Rem make a pump for 30-06 in the model 7600. I got one and love it .It dose have a mag for it . For what is stated if there is one company put more...
Forum: Lets talk trapping!
Those 120's can be a pain to try to set. For how small they are , I am doing good setting the 110's. for how it is for me. I use my setting tool mainly now. Also the one I said about setting the...
Forum: Lets talk trapping!
Here is about to make your own , need (2) 1"x1/4"x24" flat steel . then on each you do the following . 5/16" hole on center 7 1/4" down . as for the notch 5/8" down on the same end you start...
Forum: Lets talk trapping!
I will have to check on that . I will let you know . I know it is 1" flat stock and I think 1/4" thick. Just to let you know . I try the caulking gun setter on my 330's and it did not last long. I...
Forum: Lets talk trapping!
Do you have the setting tool for 220 and 330 's? If so see if that will help you to set them . I have some I had a hard time to set and that is what I used. It works for me.
Forum: Lead and Lead Alloys
I just melt the ones that end up in rejects or ones I had to pull, all gose in a tub to be melted down . Otherwise I only cast what I need . Save the alloy for when I need more for what ever it is...
Forum: Cast Boolits
You give some good points , I shoot 147 gr FN in my semi auto and feeds well. But like you said need to watch what ones will feed for your gun.
Forum: Cast Boolits
Good advice . it is best to do it with a dummy round to test this to keep it safe.
Forum: Fishing Spots
Here is a link if some like to check out areas that you like to have a idea of how it looks to fish or hunt . Go to the state and then the county and then you have a map or you can look at it...
Forum: Gas Checks
I got one of these when I got my 450 years ago , still use it . a big help.
Forum: Our Town
This is all correct .I use to work for some well companies and for the tanks that have no bladder in them. You need to drain the tank first. Normally you pump air in it to get all the water out ....
Forum: Our Town
I know at one point that there was not much 410 ammo, then when Tursus came out and then the Governor came out then it came back.
Forum: Hunting with CB's
The Redwings Black birds show up here for the start of spring . We do not have alot od crows around here. I thinking it has to do with what has been said on sprays and the virus . When I was small we...
Forum: Our Town
You load your own and do not worry about the store.
Forum: Factory & Surplus Powder
I am with you on that . I rather have printed then online . it is always there to go back on . also if there is no power you still good to go .
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |