"You can use the lee trimmer in a drill press, cheap and full proof."
I have one for sale.......
http://castboolits.gunloads.com/showthread.php?t=155143
Type: Posts; User: G__Fred
Forum: Reloading Equipment
"You can use the lee trimmer in a drill press, cheap and full proof."
I have one for sale.......
http://castboolits.gunloads.com/showthread.php?t=155143
Forum: Reloading Equipment
Buy from Harbor Freight, many others have.
Forum: Casting Equipment
I drop the spent primers in the recycle brass bucket.
Locally brass is at 2.00/pound.
My last 5/gal bucket scored $135.00.
Forum: The Star Equipment Corner
Chris, rec'ed my .3565, THANKS!!!
Forum: The Star Equipment Corner
1) Nose Down! STD bolt for press (flat surface to flat surface), GO GO GO!!!
2) Air Attachnent - I went to "Craig's List", secured a 10 gal air tank verse a compressor ($15.00). Go to the gas...
Forum: The Star Equipment Corner
The best used deal??
Found mine off of Craig's List.
Included 2 dies (358, 425).
$50.00
No, I am not making this up............
Forum: Casting Equipment
I use an old propane turkey deep frier (i.e. single burner). Went to Good Will and secured a cast iron pot for 12.00. Same tools for smenting & casting!
Forum: Reloading Equipment
Some "home made" fun.....
Picture 1 – The 3 “tumblers” (coffee cans) in the sound reduction box (kitchen cabinet w/ceiling tiles and foam).
Picture 2 – The bearing for the spinning rods (garage...
Forum: Cast Boolits
I am new to casting as well but learning from a veteran. If the bullet is solid and sound, I'll load and fire it!
However, my friend has examined some of my castings and has stated that the lead...
Forum: Cast Boolits
Thanks Trubo1889!
As I am learning it would make since to me that a good initial seal is a tad more important than the fit in the barrel (as the bullet cross the area from case (no-rotation) to...
Forum: Leverguns
I have purchased two firearms off of their "used" page.
Both were in great condition and shipping was no problem to my FFL.
Forum: Leverguns
I have a used Puma 92 and have had no problems.
My odd question, are you using commercial or reloaded ammo?
The size difference of the 38/357 is obvious, but if reloading is the 357 on the...
Forum: Reloading Equipment
Another place for untreated walnut media is Harbor Fright, in the abrasive / blasting section.
Forum: Reloading Equipment
I work on the less expensive (ok cheap) side of life.
At Good Will, I picked up:
- A plastic toy box with lid.
- A deep fryer basket.
1) I place the basket in the box
2) Brass w/media in the...
Forum: Casting Equipment
If you keep your eyes open, there are sales to be found. On Craig's list I picked up a Star Luber Sizer w/2 dies AND a RCBS Lube-A-Matic w/24 dies (yes 24!).
Forum: Casting Equipment
You can over-temp as well. If the boolits are grey or cloudy, the lead (and or mold) are now to hot.
Forum: Casting Equipment
I moved up from a 2 barrel Harbor Freight to "Bertha".
It is 3 coffee cans, in an old kitchen cabinet.
Per the spouse, it was "f _ _ _ _ _ _ loud".
I installed ceiling tiles internal and...
Forum: Casting Equipment
I use 3 parts Walnut, 1 part Lyman Red.
The 1st tumble is w/o brass and a lot of cut-up dryer sheet pieces (pull-off the dust).
When I tumble, it is 1.5 cups in a coffee can (home-made...
Forum: Casting Equipment
Secured my 61 off of Craig's List.
No idea its age, but it is older than me!
Works Great!
Forum: Casting Equipment
Many years ago, my wife and I bought the outdoor single Propane burner to deep fry chickens or turkeys. If you have one (or can secure one for cheap (Craig's List, yard sale, etc.)), it works great!
Forum: Casting Equipment
I secured my Lyman Model 61 off of Craig's List for $40. It is old and to date I have processed over 400 lbs through the 10 lbs pot.
I have no reason to complain!!!
Forum: Boolit Lube !
Good Will, the BEST parts store around!
I bought a table top fry pan w/adjustable heater.
Cut off the sides, mounted it and the Star to an oak board, HEAT FOR 5.00!
Oh, by mounting it to the...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |