RotoMetals2WidenersTitan ReloadingRepackbox
Lee PrecisionMidSouth Shooters SupplyReloading EverythingInline Fabrication
Load Data

Search:

Type: Posts; User: ScrapMetal

Page 1 of 4 1 2 3 4
Results 1 to 25 of 90

Search: Search took 0.00 seconds; generated 36 minute(s) ago.

  1. Thread: Warning!!!

    by ScrapMetal
    Replies
    24
    Views
    2,769

    I agree with Ron. It would at least be worth a...

    I agree with Ron. It would at least be worth a try.

    Thanks for the "heads up" and best of luck getting your name cleared of this mess,

    -Ron
  2. Very cool. You had to be a real man back in the...

    Very cool. You had to be a real man back in the days of the matchlock. Holding that long and accurately while you wait for the final ignition as a small explosion goes off a couple of inches from...
  3. Replies
    42
    Views
    2,055

    Very well said Bedbugbilly, I wish I could have...

    Very well said Bedbugbilly, I wish I could have put it that well myself.

    -Ron
  4. Replies
    42
    Views
    2,055

    I'm not sure what the problem is with the...

    I'm not sure what the problem is with the Wranglers. The two I have always go "bang" when they should. Granted, they are "entry level" guns and built to a price point and I don't expect them to...
  5. I saw a couple pictures of other "Hatfield"...

    I saw a couple pictures of other "Hatfield" pistols out on the 'net so it could be that actions were taken off rifles and put on pistols but it seems more likely that there were some made.

    -Ron
  6. I'm not sure what "normal" would be on that...

    I'm not sure what "normal" would be on that particular pistol but in the past single action revolvers with fixed sights would leave their front sights a little high (and shoot low) so the end user...
  7. I found a post on another message board that...

    I found a post on another message board that talked about the Pedersoli "Hatfield" rifles...




    That might give a hint as to when and how those pistols came to be.

    -Ron
  8. I have rehabilitated some very fine threads that...

    I have rehabilitated some very fine threads that haven't been hardened by using a razor blade to chase the threads. If the threads aren't too mashed up and you have a LOT of patience it can be done....
  9. Replies
    25
    Views
    1,969

    I remember reading on another forum that on the...

    I remember reading on another forum that on the sharp spire points the lead needs to be of a certain hardness. If it isn't the points can suffer deformation upon firing and play heck with accuracy....
  10. Replies
    27
    Views
    2,484

    Forum: Cast Boolits

    Good to hear. -Ron

    Good to hear.

    -Ron
  11. Replies
    27
    Views
    2,484

    Forum: Cast Boolits

    Here's a way to get some info of the missing...

    Here's a way to get some info of the missing sight. Using the Internet "Way Back" machine I accessed the last version of the website that was saved. Here is the link -...
  12. Replies
    7
    Views
    741

    WTS I'll take 3,4,5, & 6 PM sent -Ron

    I'll take 3,4,5, & 6

    PM sent

    -Ron
  13. Replies
    0
    Views
    114

    Armstrong is a straight shooter!

    Had a great deal with Armstrong, fast shipping, and the die set looked just as pictured/described.
  14. I'll take the - REDDING 45-70 3 PC #80209 EXC....

    I'll take the -
    REDDING 45-70 3 PC #80209 EXC. CONDITION $68

    PM sent
  15. Forum: Cast Boolits

    Ditto! I'll have my wallet out in a flash. ...

    Ditto! I'll have my wallet out in a flash.

    -Ron
  16. Thread: Brownells

    by ScrapMetal
    Replies
    40
    Views
    4,281

    Hornetguy, are you sure you sent your question to...

    Hornetguy, are you sure you sent your question to the correct email address? You stated that you "responded" to a marketing email that they had sent. Chances are that email is only used for...
  17. Replies
    19
    Views
    1,558

    I'll give that an amen! Deprime at the range...

    I'll give that an amen!

    Deprime at the range and drop them in a jug with water and a bit of Windex non-ammonia. Shake a bit when I get home and only tumble if I'm in a "sparkly" mood.

    -Ron
  18. Well, the "no snag" is definitely worth it for my...

    Well, the "no snag" is definitely worth it for my wife's carry as she keeps it in her purse along with everything, less the kitchen sink? Just a guess as I don't dare try to find anything in there....
  19. Robert, FYI - That "flat top" was most likely...

    Robert,

    FYI - That "flat top" was most likely the SIG 365 SAS I love the sight on that gun and the "no snag" design for CCW. I picked one up for my wife (CCW) for Christmas and am considering...
  20. Replies
    99
    Views
    8,074

    Be sure to check back in and show us what you...

    Be sure to check back in and show us what you bought. :mrgreen:

    -Ron
  21. Great transaction Phil. I'm very pleased with...

    Great transaction Phil. I'm very pleased with the parts.

    Thanks again,

    -Ron
  22. philthephlier is definitely a straight shooter - great to deal with

    I wouldn't hesitate to deal with philthephlier again.

    -Ron
  23. Replies
    36
    Views
    2,031

    I've had good luck using Kreen (made by Kroil)...

    I've had good luck using Kreen (made by Kroil) for carbon removal https://www.kroil.com/products/kreen-all-in-one-gas-oil-treatment/ I learned about it on another shooting forum.

    -Ron
  24. I'll take it. PM sent. -Ron

    I'll take it. PM sent.

    -Ron
  25. Replies
    99
    Views
    8,074

    If you want to speed up the process a bit you can...

    If you want to speed up the process a bit you can order your rifle from http://www.shiloh-ballard.com/ He charges a fee for the service but says he can get you your rifle (depending on what you...
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check