On the VT I had, the bowl cracked at the bottom , and the bolt holding the lid came out of the bottom ,and was connected only to the lid. Corn cobb media was going out the hole and onto the table. VT...
Type: Posts; User: jjnpg317
Forum: Reloading Equipment
On the VT I had, the bowl cracked at the bottom , and the bolt holding the lid came out of the bottom ,and was connected only to the lid. Corn cobb media was going out the hole and onto the table. VT...
Forum: Reloading Equipment
Can anyone give info on this model. My older VT from another company has departed and I need another VT. Thanks in advance.
Forum: Completed Deals
The part number in older manuals was 480029. Haven't seen one anywhere for sale. (gun shows, computer ) Thought I would try here.
If you shoot a P-1 9mm, what mold have you found to work best in a P-1? TC or RN ? No defense carry, but want to shoot paper,cans,etc.
Thanks
I'm looking at Accurate Mold edition ( 31-095M ) and want to know if this is considered a wadcutter to be shot at lower speeds ? It's odd looking to me and when I first saw it didn't know if was a...
Forum: Completed Deals
Received 16 Dies on Friday. Thanks again .
Forum: Completed Deals
I will take the RCBS 16 Gauge dies. Pm me your address and will get USPS money order in mail Monday.
Thanks
Forum: Completed Deals
Would like to find 16 Gauge dies that RCBS made years ago that are used on a RC press with bushing removed. Never seen a set, but were listed in an older RCBS catalog & got my interest up. Let me...
Forum: Our Town
During WW1 in 1918 and after the war in 1919, the USA was in another pandemic called the Spanish Flu. The Allies ( US/England/ France ) didn't carry much news of it because they didn't want Germany...
Forum: CB Loads / Military Rifles
In my 24/47, I use the NOE molds 326407 & 326471. Both are sized to 325. The 471 is the most accurate. Lee mold did not shoot well in my rifle.
Forum: Boolit Lube !
When I joined this site 8 years ago, I read about it and decided to make it. It's all I have used in pistols & rifles since making the first batch. I like it too !
Have the mold, but none of my Lyman Cast Manuals have the mold listed. Does anyone know what top punch this mold requires ?
Forum: Leverguns
My Henry 327Mag 20" was giving me trouble chambering SWC (B-C#932) (Saeco#325). I contacted Accurate Molds and Tom suggested RNFP 31-110DG. He was right on ! It chambers well and with Accurate#9...
Forum: Completed Deals
I'm looking for older round nose design. Pm me if one available. Thanks
Forum: Leverguns
I have been given a 8 pound bottle of H110 and know nothing of it's use in 327 Rifles. I looked on Hodgdon's site and got info on 100 grain jacketed , but I shoot an Accurate Mold 31-110 DG (gc)...
Forum: Casting Equipment
I've only read about PIDs and since I have no knowledge of electronics, building one is beyond my ability. Does anyone on CB sale PIDs ? I looked in the Vender Section but didn't see it listed....
Forum: Casting Equipment
I've had this furnace over 40 years and recently the thermostat & interior wiring were burnt completely up. I obtained stove wiring and after connecting it straight to the heating element, plugged...
In my rifles (M1 & Marlin 62 ) , I shot the NOE 311-115 GC , Lyman 311576, and Lyman 311465 Loverin. I liked them all, but each required different powders.
Forum: Leverguns
Looked on Arsenal Mold site and saw 41 mold 41-272 TC "Reeds Ammo" gc. I have 4 molds for my pistols and Henry rifle ,and none come anywhere near this weight. (heaviest is 220grain 410459) Does...
Forum: Military Rifles
I have a 1893 Mauser that is scoped. I called Brownell's and got a Leupold solid base which fit and nothing had to be altered or ground on the action.
Forum: Leverguns
I shoot a Ruger 250 and have had good luck with the following moulds under 100 grains;
NOE 260-80 grain Ranch Dog
Lyman 257464 90 grain
Arsenal 257388 89 grain SP
Forum: Factory Rifles
I am shooting a NOE 225-55 MX3 grain GC in a 223 XP100 with a 1-12 twist very well. ( 19 grains H 4895/ no filler ) Searching for a rifle now & Ruger comes with a 1-9 twist. Is this twist too fast...
I have this mold and have used it in a Ruger 77/ 250 Savage with 10" twist. I had trouble getting it to stabilize and keyholed the target when I first began shooting it. (18.5 Grains - H4895) I ask...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |