Search:

Thank you
I do load the 7 X 57 with the Lyman 287641 It shoot surprisingly well. I also shoot the Lyman 311291 in a Marlin 336, and the RCBS 30-180 in 308 and 30.06 For plinking. I use Red-Dot in...

Has anyone on here ever done much with cast bullets and the 7MM Mag and how did it work out for you. I bought a used Savage 110 in 7MM mag , I also have a Lyman 7MM 160 grain mold I use with a 7 X 57...

I resonantly bought the RCBS 22-055 SP GC mold I cast up about 400 bullets. As I tried to GC them the Hornady GC would not stay on, I had a bottle of the Lee Liquid Alox. I dipped the bullet bases in...

Two years ago I bought a bag of Starline brass and a bag of Mag-tech in 45LC. Same load and bullet used in both. I may have just gotten a bad lot. However I am still shooting and loading the Starline...

Long story short a good friend sent me some 22 aluminum gas checks. Personally I have no experience with the aluminum GCs. I have a couple questions, I assume they snap on like copper. But how well...

All opinions on Hunting, shooting and reloading forums in most cases are more opinion than accrual fact. Personally I reload and shoot both Nickel and yellow brass and have for many years. It dose...

The reason for the inquire I just added another mold to the collection its, the Lyman 429421 great mold, the bullets shoots very well in my Ruger SBH. This mold is a little of a Lube hog. And I would...

I am getting down too the end of a large supply of BAC special blend I have been using for a few years now. I have had real good results with the BAC, I use it in 7 different pistol bullets and 5...

Thanks for the comments on the Lyman 429421 mold, I picked up the Ruger yesterday, Very nice SS Black hawk used but in new condition. Looks like I will be getting on Mid-south back order list again....

Hoping to pick up a Ruger Black hawk 44 Mag 5.5 barrel this week, I have been looking at the Lyman 329421for both, Mainly a plinking round but I may use for close range white tail. Good choice or do...

Not the longest I have waited for a back order. However I got an e-mail this morning the Lyman H&I .225 die and RCBS 55 grain mold are in. back ordered just under two months back, so if you are...

You may have a pretty good wait no matter which you order. I back ordered a Lyman .225 on June 6 from Mid-south still on back order.

Another option is the Redding G-RX die.

Your rifle, game, and terrain will dictate the proper bullet, I shoot a Marlin 336 in 30-30 so I only use flat nose or flex tip jacketed bullets, tubular magazine. I hunt Pa, white tail Deer, which...

Thank you, I felt the 200-grain would be an excellent bear bullet, just not sure how the Mausers would shoot with the heavier bullets. My Mid-way USA catalog only lists a 200-grain bullet from Lyman,...

I was thinking of adding another 30 cal mold, I have a Lyman 170 grain I have taken 3 white tail deer with this bullet in a Marlin 336 in 30-30, I have used these bullets in modern sporting rifles in...

Thanks for the auto body shop idea. Some shops do mig, or tig welding and would have no trouble adding a rod to the dipper handle. I will see how the wrapped wire works first. I do use a stainless...

John boy
If I am such an anomaly and annoy you so much it seems rather foolish for you to keep reading my post. And as to real caster like all things on forums this is your opinion. If you are so...

As with all things reloading and casting everyone dose what works best for them. I mix my alloy in the RCBS pot and use bullet lube for fluxing, I have used the above-mentioned fluxes, but have had...

John Boy
If you are so disinterested why waste my time and yours even posting. I could go into why I wanted to use the old lee dipper but that to would be a waste of my time. It was a question...

The majority of my orders now go to Mid-south. I have used most all of the ones mentioned. I also did some with Gander Mountain back when they were still in the mail order business. I have found...

I may have fixed the Lee Ladle, it is steel but vary thin, un- weld able with a stick machine. I pulled the old handle off. I had a piece of stainless ¼ rod. The steel part of the Lee ladle handle is...

I cast with an RCBS pro melt pot. But use the Lee dipper for fluxing, problem is the handle on the Lee is not long enough. I have it burnt up pretty good and think the next fluxing will be the last...

Good news the mold block must be harder than the sprue screw. I ran a tap in and out of the mold block, it took a bunch of **** out of the treads. Sprayed the treads out with WD-40 to remove all the...

Thanks for the ideas, I get some spare time I will see what I can do, This 4 cavity is one of my older molds in 9MM and it gets a lot of use.