http://noebulletmolds.com, www.mp-molds.com, http://www.accuratemolds.com, https://arsenalmolds.com
all these companies make great molds I've only purchased from a couple but all I've heard...
Type: Posts; User: T-KING
Forum: Cast Boolits
http://noebulletmolds.com, www.mp-molds.com, http://www.accuratemolds.com, https://arsenalmolds.com
all these companies make great molds I've only purchased from a couple but all I've heard...
Forum: Cast Boolits
bedbugbilly I really enjoyed & appreaciate your sharing that story!
lots of awesome experiences with people's elders (grandpa or dad) shared here I myself learned on my own but hope to give my...
Forum: Cast Boolits
great stories guys that's why I asked I was hoping people would share there memories, for me it was a hurdle I had 50/50 my first session maybe even more bad then good , then took what good I had &...
Forum: Cast Boolits
what was your first casting session you consider a success & what you had to do or learned to be successful??!! what changed to turn it into a success?
Forum: Lead and Lead Alloys
be careful if your using a turky burner type it's easy to get 2 hot & burn off the precious tin that you do have & at my range I have come across zinc bullets you can buy them I saw the box called z...
Forum: Lead and Lead Alloys
whether thats the technical method idk but i always have good results doing it that way
Forum: Lead and Lead Alloys
go to Lowe's or home depot buy a small bucket n ask em to fill it with saw dust & you can buy parrifin wax on the cheap in quantity if you want & use plenty I've had many times over crud come out of...
Forum: Cast Boolits
o ya winter is all I can think of it's my reloading season indoors so I've been gathering all the lead I can to cast as much as possible now that I've got a better idea of what I should be doing that...
Forum: Cast Boolits
so far I've only had difficulty getting it to coat my 360 grain .45 flat point & in the hollow point configutation i cannot get the bottom of the hollow point cavity, boolits idk if it's the alloy or...
Forum: Cast Boolits
normally one coat does it but occasionally with certain batches I have a hard time getting it to coat well but most often there's enough that I have to tap the bullet & knock off excess, I've been...
Forum: Cast Boolits
I can get the powder coat to set just fine even with the low heat method Elvis ammo does around 200 for 15 min & the hammer test & they were fine I was having a hard time coating them well I think I...
Forum: Cast Boolits
I haven't done alot with my auto loaders yet lots with my revolvers but I work up all my loads from the lowest weight published & go up in small increments trying a couple powders atleast depending...
Forum: Cast Boolits
thank you guys I really appreaciate the input & kind words I have no one to reference in person feel a little more confident on my approach now
Forum: Cast Boolits
thank you so very much guys i did not expect such quick & informative responses
Forum: Cast Boolits
I got 2 lee Sizers .356 & .452 when i started then learned way more n bought one from N.O.E. so I just swap em out reasonably cheap n easily too many guns I have to load for
Forum: Cast Boolits
my real concern was creating an over pressure situation but that really opens my eyes to how I can experiment & maybe I should get some chamber casting alloy & check them out thank you nagantguy ! I...
Forum: Cast Boolits
I have a 9mm sig slugged at .355 then my revolver I measured out at .4515 each cyl throat so same thing I was thinking. Does any one see issue with me sizing .0015 over?
I am just starting my treck...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |