What I use https://www.harborfreight.com/lamp-and-appliance-timer-40148.html
Type: Posts; User: Bird
Forum: Reloading Equipment
What I use https://www.harborfreight.com/lamp-and-appliance-timer-40148.html
Forum: Leverguns
I bought a Taylors Uberti revolver back in 2021. Useless warranty, poor parts backup, too many excuses from Taylors. Looking at my firearm, its difficult to believe it came from an experienced...
Forum: Cast Boolits
''Even when the US Supreme Court issues a finding that California disagrees with, they just ignore it.''
There is a california politician that said '' California does not necessarily follow the...
Forum: Cast Boolits
For california hunting, you can still cast your own boolits using rotometals non lead alloy. It is on the california approved list. It is $15.00 per lb.
...
Yes. Ammo transfers must be done through a FFL, and to include a background check.
''California has a list of handguns that are prohibited from import and/or sale in the State; or actually, a list of handguns that are approved, and anything on the list is not allowed to be brought...
I am currently reviewing CA gun laws for the past 2 years to bring me up to date.
As far as I understand its ok to bring in a firearm unless it is a REGISTERED ASAULT WEAPON as defined by CA law....
Forum: Lead and Lead Alloys
I have no real use for lino or lyman#2 although I have some on hand. All bullets that I cast are with clip on ww, and are water dropped. I tried adding 50% near pure lead and a little tin to bring it...
Forum: Cast Boolits
https://hodgdonreloading.com/rldc/
Go to pistol section and use 158 grain bullet data/loads.
Forum: Leverguns
RG1911,
You need a gas checked boolit with that much rl7 powder. You are pushing towards 2,000 fps with your top loads. Clean the leading from your barrel, and use a load that gives you 1200 to...
Forum: Cast Boolits
I think 405grain has the answer.
Make up a dummy round with your 356'' bullet and plunk test it several times. Check for shavings. I doubt you will see any. Next try plunking a 357'' then a 358''...
Forum: Cast Boolits
Are you getting lead shaving when seating the round in the chamber, or when seating the boolit into the cartridge case?
Forum: Cast Boolits
Changing the seating depth will not stop it from leaving a ring of lead when the round is fired.
Your boolits diameter is too big for your chamber throat. What is the sized diameter of your...
The throats on my 2022 cattleman measure 0.366''and are made to Uberti's specification. It will not shoot boolits without severe leading of barrel. It shoots jacketed ok to 30 feet, but nothing I...
Forum: Reloading Equipment
I prefer the old style hexagonal style locks. Given a choice of the new gear type rings, I prefer the 90534 finger tighten. The type with the allen screw are difficult to use with the plastic wrench,...
Forum: Lead and Lead Alloys
Bring the pot temperature up to 625-630F, and hold it there. Then flux well. Anything that will not go back into the mix, scrape it off. You probably have too much antimony in the mix. Try casting...
Forum: Cast Boolits
It depends on what lead alloy you will be using. Spring back is a factor. I would not start casting until I had the firearm in my hands.
Forum: Reloading Equipment
lee inline feeder is what I use. Works great.
https://leeprecision.com/inline-bullet-feed-kit-35cal
Forum: Cast Boolits
I don't understand how the word eieio came to be pronounced as farm.
Forum: Cast Boolits
It appears that Vihtavuori powders that were once considered expensive, are now the same price as most popular powders.
Forum: Cast Boolits
Most powders from my supplier are 39.00 to 45.00 per lb. Alliant Reloader 16 is 75.00 per lb. plus shipping etc. Unique is 55.00 per lb.
I have a good supply on hand, and will not pay these prices.
Forum: Cast Boolits
Same thing here. Lee pro 6000 and a cz75. Can not chamber .358, but .3574 works like a charm. MP mold 125 grain round nose. 4.5 grains Unique.
I only have 1 Uberti, and that's a 357, 3 click late 2022 production from Taylors. It has .366'' cylinder throats, which is no good for lead bullets. The grips fit proud. Rough forcing cone. Shoots...
Forum: Cast Boolits
Just use a regular cast bullet and squash it in a vise, or give it a tap with a hammer on a flat surface. You only need to expand the bullet a couple of thou, then drive it through the barrel and...
Forum: Cast Boolits
I had my pins move on my mp mold. I got it too hot.
Get the mold hot again and tap the pins back in. Don't do it with a cold mold.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |