Titan ReloadingWidenersLee PrecisionReloading Everything
RepackboxInline FabricationRotoMetals2MidSouth Shooters Supply
Load Data

Search:

Type: Posts; User: Wheelguns 1961

Page 1 of 60 1 2 3 4
Results 1 to 25 of 1498

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    600

    WTS I will take the last one. Pm incoming!

    I will take the last one. Pm incoming!
  2. Replies
    8
    Views
    252

    The last couple that I got, didn’t come with lube...

    The last couple that I got, didn’t come with lube either. Maybe he stopped doing it. I put a little bit of 2 stroke oil in the cap, and use a Q tip to apply. Don’t over oil it.
  3. Replies
    8
    Views
    252

    MP molds website has a tips and techniques...

    MP molds website has a tips and techniques section with some very helpful information. Personally, I heat cycle them 3-4 times, and scrub with hot water and dawn. I oil the same as you, but I don’t...
  4. Replies
    22
    Views
    708

    I have. Never again. I got delayed ignition on a...

    I have. Never again. I got delayed ignition on a couple rounds. The primer went off, and then about a second later, the round went off. It was kind of scary. I am very happy using 2400 for that...
  5. Replies
    32
    Views
    765

    Sounds like a winner! Congratulations!

    Sounds like a winner! Congratulations!
  6. I was just trying to help. I have no idea of your...

    I was just trying to help. I have no idea of your casting experience. Maybe this will help .http://https://www.mp-molds.com/tipstricks/tip-on-easier-release-of-hp-pins/
  7. Like everyone else said, you are not hot enough....

    Like everyone else said, you are not hot enough. I cast these molds at 750-800 degrees. Are you preheating your mold? This is important because it seems that your pins are not hot enough. It takes...
  8. Replies
    15
    Views
    357

    I have a friend that seems to overcrimp...

    I have a friend that seems to overcrimp everything. I have gifted this friend many cast bullets that were fit to his specific revolvers. He always complained that his gun wouldn’t chamber the loaded...
  9. Replies
    15
    Views
    357

    Another plus for the Redding die is that it...

    Another plus for the Redding die is that it doesn’t bulge the case when a heavy crimp is applied.
  10. Replies
    15
    Views
    357

    With the Redding, you can get all the crimp that...

    With the Redding, you can get all the crimp that you want. If you adjust it lightly, it will give what looks very much like a taper crimp. Go in a little farther, and it will give you a good roll...
  11. Replies
    15
    Views
    357

    I am a believer in Redding profile crimp dies for...

    I am a believer in Redding profile crimp dies for hard hitting big bores in revolvers. I have a 480 Redding crimp die. I will check to see if there is enough extra die to adjust for 475 linebaugh.
  12. Replies
    32
    Views
    765

    If you decide to go with the wood insert grips,...

    If you decide to go with the wood insert grips, realize that there are two different sizes. There are the full size ones, and compact ones.
  13. Replies
    32
    Views
    765

    I setup the 6” for hunting deer. I just couldn’t...

    I setup the 6” for hunting deer. I just couldn’t bring myself to taking a 357. I know it will do the job, but I just couldn’t leave my 45 colt home!
  14. Replies
    32
    Views
    765

    When I had my 6”, I kept the big Hogue finger...

    When I had my 6”, I kept the big Hogue finger groove grip on it. It just fit my hand perfectly, and it showed in my shooting. I now have a Lypseys 5” with the stock wood grips. I like those too.
  15. Replies
    19
    Views
    1,226

    I ordered my mold on Weds. I just recieved it...

    I ordered my mold on Weds. I just recieved it today. That is 5 days. Last Monday, I sent a sfrb to Georgia, from Delaware. It still hasn’t arrived.
  16. Replies
    19
    Views
    1,226

    I just ordered one from MP yesterday. I will let...

    I just ordered one from MP yesterday. I will let you all know when it arrives.
  17. Replies
    32
    Views
    1,915

    When my cousin got out of reloading, he showed up...

    When my cousin got out of reloading, he showed up at my door with a truck full of bullets. There was probably 200-300 pounds of old lubed bullets, and many boxes of jacketed bullets, some unopened. I...
  18. Replies
    51
    Views
    1,746

    Forum: Our Town

    I listen to all kinds of classic rock and...

    I listen to all kinds of classic rock and country, but for reloading, it is usually Hank jr or Lynyrd Skynyrd.
  19. Replies
    14
    Views
    1,503

    I cast mostly in the spring and fall. It is too...

    I cast mostly in the spring and fall. It is too cold in the winter and too hot in the summer. If I won’t be casting for awhile, I drain the pot. This way it can be fully clean before casting again....
  20. Replies
    8
    Views
    524

    Lee six cavity handles work fine. I have a couple...

    Lee six cavity handles work fine. I have a couple dozen mp molds and have never owned a set of mp handles.
  21. I think you are overthinking it. I use old cookie...

    I think you are overthinking it. I use old cookie sheets covered with non stick foil. Works great! Over the years the foil has become very thin. Now you can’t get more than one use with the foil.
  22. Replies
    5
    Views
    460

    WTS I will take one. Pm inbound.

    I will take one. Pm inbound.
  23. Replies
    74
    Views
    3,366

    Another Unique fan.

    Another Unique fan.
  24. I load mine with 2.5 grains of bullseye.

    I load mine with 2.5 grains of bullseye.
  25. Replies
    18
    Views
    1,426

    Yes, I am also addicted! I have Noe molds,...

    Yes, I am also addicted! I have Noe molds, sizers, expanders, gc seaters, even a NOE mold guide.
Results 1 to 25 of 1498
Page 1 of 60 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check