Strange, I tried it in Google and it didn't work. Just tried it in Microsoft Edge and it opened:killingpc
Type: Posts; User: BrianL
Forum: Classics & Stickies
Strange, I tried it in Google and it didn't work. Just tried it in Microsoft Edge and it opened:killingpc
Forum: Classics & Stickies
What happened to this link? I used it quite a bit and have tried to get there. Has it been moved?
I am following this post to find a good way to use up a pound or more of old stock. We realize that it is discontinued.
Forum: Reloading Equipment
1 Dillon 650
2 Old style Lyman Spartan T-presses (Turret 6 station)
1 RCBS Rock Chucker
1 RCBS RS
1 Lyman Spartan single stage
3 Mec shotshell presses
3 luber/sizer iron presses (2 RCBS & 1...
Forum: Cast Boolits
I had the same experience and also found that the Sage standard sized check was tight after going through a Lee sizer
Forum: Cast Boolits
I was hoping that this was the case. I did shoot twenty of them loaded with 15 gr of 2400 in 5 shot groups at 50 yds. Shown are the first from a clean barrel and the last.318674318675
I went ahead and loaded 20 rounds with 15 gr of 2400 and was very happy with the results so far. The rifle is a custom Swedish Mauser by Flaig (Flaig's Ace) Showing the first and last targets @ 50...
Forum: Cast Boolits
Is the forward band also .268? Mine is .268 on the rear band and only .263 on the forward band.
I just purchased the new Lee mold for 6.5 mm and planned to use this bullet in both a Creedmoor and a Swedish Mauser. I cast about 100 bullets today and after the mold warmed up, it dropped very nice...
Forum: Lead and Lead Alloys
Nope, not acceptable at all. The time spent till now was not given the value it deserved but going forward, it has increased in value many times over. The hourglass only has so much sand, value each...
Forum: Cast Boolits
Put together a bucket of 32 Winchester Special with RCBS 170 (actual weight with check 182gr) for the grandkids to practice their offhand.317749
I have used it to show people looking to trade for old surplus guns, just what they were getting
I also have the Teslong in both rifle and pistol length and have found them to be excellent inspection devices. What some folks do not know is that the mirrors can be focused for different bore...
Forum: Leverguns
I had two Rossi 92's, one in 44mag and the current one in 357. Both fed/feed everything but why are they so danged short????
Forum: Deep Theological Discussion
The USA will be judged for its LACK of rebellion, when loud screamers that represent 7% of the masses hold sway, we all have no one to blame. Good and fine people who just want to get...
Forum: Deep Theological Discussion
An elected government should be the subject of the electorate. When elected 'Officials' decide what their constituents want, rather than asking them, they no longer are representatives and have no...
I was an avid user of Unique until you could not get it anymore so I switched to Universal. I stashed the last of my Unique for 38 special.
I have been using 231 for .380. 9mm, and 45 ACP for the...
Forum: Factory & Surplus Powder
What has been your experience with Shooters World Buffalo Rifle. My understanding is that it was sort of equivalent to 5744? Other than in 45-70, I tend to have a lot of unburned powder and dirty and...
Forum: Factory & Surplus Powder
I have ALMOST bought Trailboss a couple of times but could not get past the price.
Forum: Our Town
Oldest smokeless gun is a 1908 Remington repeating shotgun (pre model 10). That has the tightest full choke that I have ever seen. I use 3/4 ounce loads on squirrels and it is lethal out a long ways.
Forum: Leverguns
My grandfather had a rifle hanging on the wall forever, a Winchester Model 64 rifle in 32 Special. My father wanted one just like it but could only find one in 30-30. My older brother got that one...
Forum: Lead and Lead Alloys
By the way, when I first started doing this, I was skeptical and thought that you would end up with a mass of lead dust. So I pounded 50 300 gr 45 bullets into a very tight group (that is my story)...
Forum: Lead and Lead Alloys
They are pressure tanks from expansion tanks or compressor tanks. I cut off the tops. Take junk tires, cut the treads off and slice the sidewalls into chunks. I stand the tank up and line the...
Forum: Factory & Surplus Powder
I have had no standout loads in 300 BLK with l'LL gun. I went through a couple of pounds and found that H110 for supers, and 1680 for subs, covered my needs. Ant the other issue was that the L'll gun...
Forum: Lead and Lead Alloys
Third clearing of the 50 yard mulch trap this year. So far 87 lbs. The pistol trap is next and those are mostly 200- 230 gr 45 acp. Some of these have been downrange in some form several times. The...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |