I probably have more HiTek powders to last a lifetime (for my production rate that is). I had some zombie green, candy apple red, and brown copper in the fridge for several months. The base turned...
Type: Posts; User: Shotgundrums
Forum: Coatings and Alternatives
I probably have more HiTek powders to last a lifetime (for my production rate that is). I had some zombie green, candy apple red, and brown copper in the fridge for several months. The base turned...
Forum: Coatings and Alternatives
Hey Trev, hey candyboolit people! Happy holidays! I don’t post much, but I’m in here from time to time.
I can attest to this; especially, the “mystery” alloy part. I’ve been using muriatic acid...
Forum: Coatings and Alternatives
Greetings, guys! Haven't been on here in a while, nor shooting much since getting stationed in Okinawa.
Has anyone tried any of this coating yet? It does resemble hitek a lot.
J
Forum: Coatings and Alternatives
Bruh, with clip-on wheel weights...eh... you could be right. But, I was chasing my tail with this once. I had bullets pass the smash and wipe test. BUT...they would fail the smash test a week or...
Forum: Coatings and Alternatives
It has been a while for sure. Everything is well, hope all is well in Oz brother.
I have one year of assignment tour remaining, but I’m strongly considering extending two years, the last two...
Forum: Coatings and Alternatives
Hello, fellow boolit casters/coaters!! I haven’t been on the forums in a couple of years as I’ve been stationed in Okinawa since 16. It’s great to see the hi-tek and other coating methods are still...
Forum: Coatings and Alternatives
Try again by mixing and stiring the dry powder. This stuff can settle and components can separate. Probably happens in transient, shipment, bullet company distribution and packaging.
I ordered...
Forum: Coatings and Alternatives
"thin" coating as mentioned was my tail-chasing problem for a little while initially. While thin coats are stressed for good mechanical bond, too thin just isn't enough barrier. Using a wide 3...
Forum: Coatings and Alternatives
Man that's a long bullet. I have their 35-135Z for 9mm. COAL 1.10 3.5- 3.6gr 231 for subsonic/suppressor use.
Forum: Coatings and Alternatives
Hey Popper,
it sounds as if you're after decent accuracy with rifles and cast bullets. While it's not a race horse production-wise, you could try pouring single-cavity bullets while monitoring heat...
Forum: Coatings and Alternatives
163534 Not powder coat. But the red on the bottom is epoxy resin coated, shoved at 1200fps. The other is HT bronze 500 fired at same vel. I tend to use the epoxy methode in guns that have...
Forum: Coatings and Alternatives
Yeah it's a mystery. Thicker coats would need longer evaporation time or it'll flake off.
Further, if it's really saturated, you'll get cratered bubbly coating.
Forum: Coatings and Alternatives
Yeah, wipe off is under-cured coating, no bueno (wipe for 30 whole seconds). Make sure your oven temp is correct. From there adjust as needed. Don't overload your oven, internal circulation is a...
Forum: Coatings and Alternatives
Success!! My 38/357 D funnel experiment worked. I fashioned a hollow spacer to place between the top of the funnel and the powder hopper aperture leaving no clearance for loose funnel play. ...
Forum: Coatings and Alternatives
Well, I use hardball or similar as well. I may be coating too thin... From the OZ practices yeah, I coat too thin��
I am still experimenting with the 38/357 D funnel and getting it to work for 9mm...
Forum: Coatings and Alternatives
Maybe my practices need tweaked and I'm coating too thin... I usually use 1ml per lb. Even less on the first coat; first coat say 3lbs I might put 2mls with a mini splash of solvent to pick up...
Forum: Coatings and Alternatives
Well, scheisse. I'd be your nickel plated man if geography wasn't an issue.
I'm doing an experiment with my Dillon D 38/357 powder funnel and hopper. After loading 300+ 2x coated 9mils, I...
Forum: Coatings and Alternatives
Now now now, Trev... At one time you were saying MEK took longer. I personally can vouch for it taking longer as I have been using MEK almost exclusively. Plus as the coating solution ages...
Forum: Coatings and Alternatives
I'm sure Trev was just poking n kiddn around.
Forum: Coatings and Alternatives
Silver?..... Now there's a challenge. You listening , Joe? Congrats on the blue. Those are powders Yes? I like it. That green is ******. Like a leaf beetle shell green.
Forum: Coatings and Alternatives
Here is what you wanna do with your jag patching. I use an old white cotton t shirt for all gun cleaning. This way I can make what I need, and I'm cheap lol.
Make an even rectangular, long strip...
Forum: Coatings and Alternatives
You might try what I did with my glock barrel.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |