Price now includes shipping for the first 48 states
Type: Posts; User: RU shooter
Forum: Completed Deals
Price now includes shipping for the first 48 states
Forum: Completed Deals
( sold pending payment )****Need to sell this family owned Winchester 94 src in 32 win spl. based on the search of the sn was made in 1928 it’s all original and unmolested no buggered up screw...
Forum: Completed Deals
I have an early Dixie souther poor boy flinter I swapped out the original barrel few years back with a 7/8 green mtn. Barrel it’s a 36” not the original 42 “ length bore is good not brand new but...
Forum: Muzzleloading.
JB weld won’t work well I tried once it lasted about 10 shots . Solder or riveting is the way to go
Forum: CB Loads / Military Rifles
I’d try 5-6 grs of bullseye with those and see if they will shoot with that undersized nose . It’s a low power load but will still shoot 10’s at 50 yds with a bullet it likes . I’ve shot many many...
Forum: Gunsmithing Tips & Tricks
Thanks all for the help everyone I got the Winchester all stripped down and the offending screws tightened up nice and tight as I could with the tiny screwdriver and blue lock tight , should be good...
Forum: Gunsmithing Tips & Tricks
Thanks all , the more I looked at it I figured it would be a pain . I’m gonna watch some videos and learn how to strip it down to be able to access the inside of the receiver . Still very close...
Forum: Gunsmithing Tips & Tricks
I looked up the schematics that bar is the cartridge guide bar if it’s any help for a solution
Forum: Gunsmithing Tips & Tricks
Gentlemen my friend wanted me to look at a win 94 30/30 that the action wouldn’t fully open . I told him I’d take a look at the ole gal . So I start to get it apart and I’ve found the issue, but...
Forum: Muzzleloading.
If you can’t pull it out drill out all that you can don’t try to melt it out you’ll just burn up the stock . I have a 24 ga (58 cal) smoothbore with a 30 “ barrel and it only weights 6 lbs and...
Forum: Military Rifles
fully agree with you on the myth . I’ve shot cast in quite a few different gas guns may pick up a flake of silver now and then in the gas system but far far from effecting function . Now just maybe...
Forum: CB Loads / Military Rifles
That was my go to bullet next best was the 312-185 lee and as you said about the same as surplus ball at 100 yds
Forum: Muzzleloading.
Don’t know if coil springs in the lock are a step forward or backwards well I do BUT , imo nothin wrong with properly made main and frizzen spring. Compare a chambers late ketland to a TC ...
Forum: Muzzleloading.
Our Wally mart usually carry’s them around deer season It’s one of the few places near me in western Pa that does as flinters and in lines are more popular
Forum: Muzzleloading.
I bought several pounds of it a years or so ago and the it’s just a big mix of grain sizes . I took the time to sift it all off and about 75%was 2-3F granulation best as I can figure The stuff I...
Forum: Muzzleloading.
That’s odd on my 200 gr 45 cal I can just about thumb seat them to the top band and then a firm push on the rod , once it’s in the barrel I can seat it on the powder with two fingers on the rod . If...
Forum: Muzzleloading.
Id remeasure the barrel (land to land) and see if you get the same reading. And look for a ball size that will work for it . I don’t think a very undersized ball and a double patch is conductive to...
Forum: Fishing Rods
Depends what your targeting on the pier , I’ve done a good bit of fishing off the obx piers but am mainly trying for the smaller eating size fish , if that’s the case a a 3-4000 size spinning reel...
Forum: Shot Guns
Little late to this post but I’ll throw my odd duck pick in the mix . It’s a Remington 17A , It’s an old family gun from my dads uncle . Only made them in 20 ga and she’s light and shoulders...
Forum: Muzzleloading.
Agree with the above post a fouling covered patch will tarnish up brass in short order
Forum: Muzzleloading.
What I ended up doing was sifting it all off in different screens, the bulk of it ended up being 1.5-3F in granulation . I just mixed the 2-3F into one lot and have used near a pound of it in my...
Forum: Completed Deals
Anyone have a lee .562 ball mould they could part with ? Would also be interested in a hundred or so cast ball similar in size for my 24 ga (.580) smoothbore pm or email me with a price shipped to...
Forum: Muzzleloading.
Thanks all for the thoughts and opinions , Yes I hear what some of you are saying about the type of kit it is . As the guy explained to me he really wants to get into flintlocks/black powder but he...
Forum: Muzzleloading.
I’d consider that a bargin for your level of craftsmanship Sir .
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |