Slightly thicker paper will be better than thinner if the patched bullet is a loose fit in the bore[I patch to bore diameter].One thing I've done is make a custom sizing bushing and final size the...
Type: Posts; User: 25ring
Forum: Smokeless Paper Patching
Slightly thicker paper will be better than thinner if the patched bullet is a loose fit in the bore[I patch to bore diameter].One thing I've done is make a custom sizing bushing and final size the...
Forum: Smokeless Paper Patching
You can patch to bore with smokeless powder. I've been doing it for quite a few years with a .443 slick patched to .450-.451 in a 45-90 using both WC 872 & 867 and IMR 3031. In a 45-90 you do need to...
Forum: Smokeless Paper Patching
Kurt,If you show up at Alliance again I'll show you my smokeless PP loads.---Mike
Forum: Casting Equipment
Best answer is a separate PID then you can run it with any pot you want,and it will be far more accurate.
Forum: Smokeless Paper Patching
I started out duplexing with RL-7 when I was using greasers now with paper patching I load them without since there's a lot more case capacity especially with the 90.Other than that you pretty much...
Forum: Smokeless Paper Patching
I used to use a 3 wad stack in the 90 to take up excess space in the case,now I use a combo of floral foam and a .060 LPDE wad compressed .10. That's how much bullet is in the case. Primers seem to...
Forum: Smokeless Paper Patching
I've been using this for 45-90,45-70 38-70,38-55. I run a .443 slick patched to .450-.451 in the 70 and 90.My Sharps has a tighter bore than my HighWall and uses a thinner paper for a slight...
Forum: Smokeless Paper Patching
I've been shooting patched to bore paper patched bullets for quite a few years using WC872 & 867 also IMR 3031. Patched bullet is .100 into the case and lightly taper crimped. Accuracy is just as...
Forum: Factory & Surplus Powder
Blue Dot also works quite well in 32-20 and 25-20 loads around 6 to 7 grs.
Forum: Military Rifles
There is plenty of adjustment with either the unertl or lyman targetspot scopes. I have an 8x unertl reproduction scope on my CMP vintage sniper and a 14x unertl on a 1903 converted to 22rf. Both...
Forum: Gunsmithing Tips & Tricks
Hornady One Shot cleaner and gun lube
Forum: Cast Boolits
The best way I've found was shown to me years ago.Take a jag and get a patch that is so tight that you have to tap it through with a mallet,soak the patch in turpentine and if you have any lead it...
Forum: Smokeless Paper Patching
I've been using WC872 and a 4gr kicker of RL-7 for years in my 45-70 Trapdoor. Pressures and velocity are in the black powder range and my chronographed SD's are in the single digits. FWIW
Forum: Cast Boolits
Take a patch on a jag large enough that you have to tap it through the barrel,soak the patch with turpentine. You'll be amazed at the amount of lead that comes out. FWIW--Mike.
Forum: Reloading Equipment
Use a media separator for separating the brass and pins.Then dump the pins into a 5gal bucket lined with a 5gal paint strainer bag.You can rinse the pins out in the bag and hang it from the handle to...
Forum: Black Powder Cartridge
Another good load with WC872 is 4grs RL-7 and 54grs of WC872 with a 466gr mini-groove bullet. This is a mini-groove that has been shortened 1 band.
Forum: Black Powder Paper Patching
I use Pacon tracing paper .0025 with a BACO .443 slick.Makes for a slight interference fit in my .450 bore.Since your bore is .4485 the thicker paper may help.FWIW--Mike.
Forum: Reloading Equipment
Most of my case scratching went away when I switched over to stainless steel pins for my case cleaning duties.Cases come out perfectly clean inside and out with no dust or grit on the outside of the...
Forum: Black Powder Paper Patching
I cobbled together one from PVC pipe and caps. I used a spring out of an old Hunter rotary sprinkler head,works great! FWIW --Mike.
Forum: Black Powder Cartridge
Just pick up an old cookie sheet,dump the brass on it,pre heat your oven on the low setting usually 200.The brass will be dry in about 15min or there about.No muss no fuss.
Forum: Cast Boolits
After you've tried all the methods posted for removing leading and think you've got the bore cleaned out,take a very tight fitting patch soaked with turpentine and tap it through the barrel.You'll...
Forum: Black Powder Cartridge
As far as wiping or blow tubing,it depends on the temperature of the barrel.If the barrel gets so hot that you can't keep the fouling soft by blow tubing you'll have to wipe.Relative humidity,air...
Forum: Casting Equipment
The one and only time I had brass staining was when I shut off the tumbler and let the brass sit in the dirty solution.Your problem isn't the cleaning solution,it's letting the brass sit in the dirty...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |