Search:

I use a Lee 4-20 pot. I use a lead thermostat. The lead is from wheel weights. The day before I did 400 9mm and .380 ACP bullets basically using the same lead and they came out great.
The molds are...

What size are those bins?

Some failed 9mm and .380 ACP hollow points. I am not sure if the lead or molds are not hot enough or what could be wrong. I was careful and prepared the molds221677 as usual. Any thoughts?

Thank you for all who took the time to respond. I have some great info to get me going. One issue I am working on is my belief that is if 2 asprin are good for a headache, then three are better....so...

As a new caster, I tried the pc method and did not like it. I decided to use the 45-45-10 Tumble Lube that has been used to years.
Am I missing something by deciding not to use power coating and...

For a while I was trimming 9mm cases to 9x18 Makarov. I have the trimmer with the drill adapter and the Lyman Case Prep. I have since got rid of my Makarov (except for some bullets).
I am casting...

I use my Lee Hand Press and my RCBS priming tool in the House. We live in Yuma Arizona and it was 111 yesterday and the shed gets a bit warm this time of year. I try to get up a 5 am and out by 6 to...

I know the feeling about time. I got more done at home working one and one-half jobs and raising 3 kids than I do now being retired

I would be interested in watching them and then pass them on.


Sent from my iPad from Yuma AZ using Tapatalk

After a couple of years of buying bullets, I decided to make my own. I have a mold for the 9MM and also one for my 380 ACP. I researched the Internet and even After the influence of Elvis Ammo, I...

I wet tumbled 1000 .380 ACP brass and expanded 100 or so 9mm casings. All while painting our mobile home for a few hours and going to the supermarket. And I am 69. And sober. Life is good.


Sent...

Thanks for all the advice. I did have the die touching the adapter. I am usually so very careful in ever step I do. All is working fine. Thanks again.

I need help. All my prep was done correctly. The bullets are Berry Bullets, .380 ACP 100gn RN. These cartridges were NOT crimped, just seated within specs at .962. I am using a Lee seating die. Does...

I am getting into casting but not at the to be ready to cast. I am also torn between 45-45-10 Tumble or powder coat.
So I need some raw 9 or 380 bullets, any style or any weight to test my Lube...

Does anyone know where I can lead boolits not lubbed and not sized? I don’t want to bore anyone with the reason why. 9mm and .380 ACP.
Thank you

Where o where does one get bee’s wax in chunk quantity? If have looked and looked and only find small amounts for a small fortune?

On page 28 of the SAAMI manual, it states the lenght of a 9x18 Makarov case should be .713-.010. Does anyone know if the -010 means that .010 is a tolerance range to trim the case between .703 to...

Is there any interest in a .365 Lee sizing die or a 6 cavity 9x18 bullet mold?

Has this been done successfully? I want to do it on cast 38 & 40. It would be satisfying..


Sent from my iPad from Yuma AZ using Tapatalk

According to some research I did, Although one does not need FFL license, it was advised, as I was advised here, it is not a good idea.

People. ... it is a liability issue with reloaded ammo. If...

Is there a market for selling reloaded ammo at gun shows and flea markets?


Sent from my iPad from Yuma AZ using Tapatalk

What a tragedy about the lead pot!


Sent from my iPad from Yuma AZ using Tapatalk

I want to cast 38-158 SWCHP. Where is a good source to search for a mold?


Sent from my iPad from Yuma AZ using Tapatalk

Thanks


Sent from my iPad from Yuma AZ using Tapatalk

Can I power coat HP bullets?


Sent from my iPad from Yuma AZ using Tapatalk