Yes, I am just learning and shake and bake is what I'm doing, is the spray a powder? and do you also spray the bottom?
Type: Posts; User: msta999
Forum: CB Loads / Military Rifles
Yes, I am just learning and shake and bake is what I'm doing, is the spray a powder? and do you also spray the bottom?
Forum: CB Loads / Military Rifles
how do you get yours to be so smooth and shinny? mine have small lumps in them and are dull.
Forum: CB Loads / Military Rifles
Thanks, but I don't have any of these powders. I just got my gas checks, I powder coated the bullets and installed the gas checks. These are some powders I would like to use up:
AL5, AL7, AL8,...
Forum: CB Loads / Military Rifles
I have gas checks coming, but want to try out a few of my cast bullets, anyone know where I can find load data for this? probably around 1150 vel.
what wt bullet and which primer? I have a bunch of red dot I need to start using again!
Forum: Cast Boolits
I was wondering if the is one lead bullet all three rifles? Im planning on getting a mold for this or will I need multiple molded? Since they are all .30 cal, only one sizer should be needed.
...
Forum: Completed Deals
a couple hundred would be nice....
some dies too...
These are the sabot looking slugs, I am using the "Sabot Slug bullet mold .410 GA (10.4 mm) Lyman style, reloading, AS-company" off E-bay and they look good. They seem to run about 123 grain, I am...
I dropped the pre crimp down a little so the hull is closed more, before the crimp and so far that has worked, I need to buy one of the better pre crimps though, mine is new and keeps coming off the...
yours looks a lot better than mine! I have been thinking about getting a complete new die set, this one is pretty old. I did buy a new pre-crimp but it sticks to the hull, I can back it off till it...
These are thug slugs and the wad is connected to the slug. No cards and the recipe doesn't call for it, I am having trouble getting the wad/slug combo to seat the same on each hull and have to use...
I am doing a fold crimp. I'll look at the tool you mentioned, thanks.
I am using a Mec Jr, older one, and I noticed sometimes the slug/wad combo, doesn't look deep enough, so I will take it up to 20 - 25 lbs to push the slug down a little more, I normally set it to 15...
AA hull, Thug slug with wad attached - 8gram, 11 grains of 4756, win 209, fold crimp
Hi all, I'm having trouble with my crimp or about 25 percent of them. Here is a pic, does this look like the slug is not down far enough? or something else?
288166
288167
I ordered a couple different types from BP, I'll look at options, once they are here.
.410 is my latest caliber I have been loading for and was wondering if anyone was loading or casting slugs? I did a search and came up with zero! I have read using 40 cal. bullets are unstable.....
Oh, Sorry! I saw the buy now, which I had never seen before and thought they were making you buy the datal...oops!
I went to the Hodgdon site to look at some slug data and found out you now have to play if you want to see how much powder to add to the load.
Thsnks!
Im looking for a good reliable load for bear, so yes, I want a stout load
I have no trouble finding data for Sabot slugs with Gold Medals, just these DGS.....or should I just be looking at the weight of the slug and go with that? I did notice different slugs of the same...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |