Reloading EverythingWidenersInline FabricationLee Precision
Titan ReloadingLoad DataMidSouth Shooters SupplyRotoMetals2
Repackbox

Search:

Type: Posts; User: Hi-Standard

Results 1 to 11 of 11

Search: Search took 0.00 seconds.

  1. I wonder if you could attach the wad somehow and...

    I wonder if you could attach the wad somehow and that would prevent tumbling like a Remington Buckhammer. The wad would trail behind and stabilize the slug? Maybe attach the wad to the lead with a...
  2. Jeese that's impressive. They didn't seem to...

    Jeese that's impressive. They didn't seem to tumble either. Usually Foster slugs are nose heavy with a hollow base to fly straight and not tumble, but yours are all solid? Did any of the shots...
  3. Replies
    3
    Views
    1,487

    Larry thank-you for that very informative read. I...

    Larry thank-you for that very informative read. I was unaware that low charge detonation, and that's what I was refering to, had been disproven. I am very interested this summer in shooting some cast...
  4. Replies
    3
    Views
    1,487

    Pistol Powder In Fat 30's

    I've just come upon a quanity of AA#2, AA#5, 700X, and 800X. I was wondering about your experiences with gas checked/non-gas checked cast bullet loads in fat 30 calibres such as 303 Brit, 7.65...
  5. Replies
    26
    Views
    14,132

    So AA#5 being a little faster than Unique and...

    So AA#5 being a little faster than Unique and AA#2 being a little slower then Bullseye should be ok without fillers? I guess 800X maybe a little too slow?
  6. Replies
    26
    Views
    14,132

    Not trying to hijack here, but have any of you...

    Not trying to hijack here, but have any of you guys had problems using pistol powders without fillers? I've only ever used Unique without fillers in my cast rifle loads. I have 700X, 800X, AA#2, and...
  7. Replies
    18
    Views
    3,904

    Forum: Cast Boolits

    gray wolf sounds like impurities in the melt. Try...

    gray wolf sounds like impurities in the melt. Try fluxing with wax toilet gasket that's what I use. And flux often as well. Also wash your mold out in case there is grease or dirt in it as well.
  8. Replies
    11
    Views
    1,730

    Forum: Leverguns

    Do you shoot cast with this rifle pumpguy? That's...

    Do you shoot cast with this rifle pumpguy? That's probably a silly question on this board. Thank's for the input guys, you've given me a lot to think about!
  9. Replies
    11
    Views
    1,730

    Forum: Leverguns

    Marlin Lever

    I had my eye on a Marlin Lever in 44 Rem. Mag until I noticed it had a micro-groove barrel. I would be shooting cast mostly, and I have heard terrible reports about cast bullets and micro-groove...
  10. Replies
    13
    Views
    1,445

    Forum: Cast Boolits

    I've got a Remington 700 SPS in 30-06 that can...

    I've got a Remington 700 SPS in 30-06 that can have two holes touching at 100 yrds. Then on shot number 3 the groups start to look like my 1100 using number 9 shot!
  11. Replies
    1
    Views
    1,144

    Forum: Cast Boolits

    N-69 Powder

    I got 2 pounds of the stuff from Higginson Powders in Ontario. I contacted Andrew Higginson for some load data, and all he could supply was 358 gr. bullet for .357 Mag. and 240 gr. for .44 Mag. He...
Results 1 to 11 of 11
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check