I can normally see a small amount of light around the pins on all of my RG molds, it's just the nature of machining tolerances and retaining the ability to open and close them freely. You need to...
Type: Posts; User: bsev81
Forum: Cast Boolits
I can normally see a small amount of light around the pins on all of my RG molds, it's just the nature of machining tolerances and retaining the ability to open and close them freely. You need to...
Forum: Cast Boolits
Your best bet is to call, Al is great about picking up the phone especially early in the morning. Ask him if it's on the list of molds to be ran, which I would bet it is. The problem is the list is...
New mold day is the best, except for that dang break in period.. Very cool, I remember when this bullet was designed and didn't know you could buy the mold for it. My 1:7 barrel stabilizes the NOE...
Looks like the gator checks are in short supply at the moment, I normally get them through NOE, bayoubrassandammo.com or Sages Outdoors. Currently Sages appears to be the only one with them in stock....
Forum: Coatings and Alternatives
https://noebulletmolds.com/site/product-category/bullet-moulds/338/htc339-315-fn-bz1/
Forum: Coatings and Alternatives
I almost exclusively shoot coated cast in my 338 Spectre's with 1:6.5 twist. Mostly subsonic, no issue stabilizing 315gr down to 740 fps. I haven't done much with supers but 200gr checked and coated...
Forum: CB Loads / Military Rifles
I've done quite a bit of back and forth with Taco regarding the 458 Socom and 338 Spectre over the last few years.
For the NOE HTC459-500-SP (PC and sized .4595") @ 2.18" with CCI 350s
Accurate...
I have been a fan of No. 5 for years but never tried it in 357 until now. Dad asked me about a medium power plinking load for range days.
I recently got the NOE HTC358-154-RF, got some powder...
Forum: Hunting with CB's
Good information and great story telling. What part of South Carolina, I just started hog hunting this year in Kershaw county. Bagged one 200 pound boar and I was hooked, talk about good eating!
I...
https://web.archive.org/web/20120418083147/http://john-ross.net:80/loading.htm
Getting harder to locate the John Ross spreadsheet these days.. 700 grain is at the bottom with 7-8 powders listed.
Forum: Group Buy Discussion
Lakehouse, not sure if it will really matter since you're getting a VS up and running but can you remove me from this list? I thought the Cast Boolits mold would not be run again and i'm curious to...
Forum: Group Buy Discussion
Count me in for four, please and thank you.
Forum: Gas Checks
Just my two cents here as I am in the same boat as you, I purchased my first PB checks last week. My first attempt was with bullets cast and powder coated a few months ago and I snapped a press in...
Forum: CB Loads / Military Rifles
Using the NOE HTC 354 grain bullet I started with 28 grains of W296, yielded 1420 fps in my 10.5 barrel.
Forum: Group Buy Archives
It's not a round nose design we're talking about but there is a group buy discussion started at NOE for a 100 grain bevel base bullet.
http://noebulletmolds.com/smf/index.php/topic,2368.0.html
Forum: Group Buy Archives
If using chrome, there is an add-on to fix it. If you search for Photobucket hotlink fix and install it, should fix the issue. Works for desktop/laptop PC, mobile still shows the stupid message.
Forum: Cast Boolits
Check your bullet size, I ditched my Lee 175 grain mold for my G29 because it was dropping undersized at .399".
Forum: Cast Boolits
It is the same mold, unless they went back and fixed it since doing the group buy run. There was plenty of interest, the intent was to make it 168 grains but after cutting the molds the final product...
Forum: Cast Boolits
I'm not sure I qualify for "mentor" status but always willing to try to help, what area of upstate? I'm in Camden a little closer to the garnet area, takes me about an hour and a few to get to Fort...
Forum: Cast Boolits
Yessir, it was originally designed as a boat tail but due to demand in 300 blackout Al agreed to offer a plain base version as well.
http://noebulletmolds.com/NV/index.php?cPath=84_461
Forum: Cast Boolits
Also curious to see what you're shooting these from.
I have the 174 grain version and have been contemplating this mold, tuned in for results.
These HTC molds wreak havoc on your wallet....
Forum: Cast Boolits
Shdwlkr
First and foremost, thank you for your service.
Since I started shaving my head I've always had a beard to some degree, my face never fared well shaved smooth. I can handle a breeze on...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |