Reloading EverythingInline FabricationRotoMetals2Repackbox
Lee PrecisionWidenersTitan ReloadingMidSouth Shooters Supply
Load Data

Search:

Type: Posts; User: HCH

Page 1 of 3 1 2 3
Results 1 to 25 of 51

Search: Search took 0.00 seconds.

  1. Heaviest? 260 WFN.

    Heaviest? 260 WFN.
  2. Replies
    20
    Views
    2,164

    I had one for awhile. It's a great carry gun!! ...

    I had one for awhile. It's a great carry gun!!

    I just ended up trading it on something else.
  3. Replies
    12
    Views
    1,297

    I had an original Shield in .40 with the safety....

    I had an original Shield in .40 with the safety. I intended to carry it safety off. That was all fine and dandy until I pulled it out one day and the safety had been applied. I found a youtube video...
  4. Replies
    44
    Views
    5,456

    Forum: Leverguns

    H110 for hot loads, titegroup for plinking loads.

    H110 for hot loads, titegroup for plinking loads.
  5. Replies
    11
    Views
    1,272

    That's a fine rifle!

    That's a fine rifle!
  6. Replies
    0
    Views
    519

    WTS--350 Rem Mag Brass

    I counted 631 pieces, but I could be off by a few. I picked this up at an auction last week. The gentleman that processed was a well known gunsmith/reloaded in the area. As far as I can tell, it was...
  7. Replies
    37
    Views
    2,572

    I would powder coat and push through size if...

    I would powder coat and push through size if needed.
  8. Thread: Casting Table Top

    by HCH
    Replies
    28
    Views
    2,487

    Looks a whole lot better than my setup: a Lee...

    Looks a whole lot better than my setup: a Lee 20lb sitting on a 1×12 laid across the tailgate of my pickup.
  9. Replies
    0
    Views
    200

    WTT .458 Plain Base Gas Checks for .452

    I have about 750 Sage Outdoors .458 Plain Base gas checks. I would like to swap them for .452 plain base gas checks.
  10. Replies
    7
    Views
    627

    Forum: Leverguns

    Thanks guys!

    Thanks guys!
  11. I've load a whole lot of 223 for 3 gun. I use...

    I've load a whole lot of 223 for 3 gun. I use standard dies and whatever SR primer I have on hand at the time.
  12. Replies
    100
    Views
    8,035

    Forum: Leverguns

    I hope they'll put out good guns at decent...

    I hope they'll put out good guns at decent prices.

    I dont expect the today's ruger to start offering guns in old, obscure chamberings.

    Perhaps they can build a box-mag lever rifle to compete...
  13. Replies
    985
    Views
    120,577

    This monstrosity.276428

    This monstrosity.276428
  14. Replies
    7
    Views
    627

    Forum: Leverguns

    Let's Date Another Savage 99

    I have a savage 99 in 30-30. Serial number 304818, and the lever boss has an M stamped on it. It has the rotary magazine and a carbine buttplate.


    When I go to the savage dating site, the serial...
  15. Replies
    16
    Views
    1,225

    Hard to go with one of them! That Alex...

    Hard to go with one of them!

    That Alex trigger is great too if you want to upgrade it.
  16. Replies
    29
    Views
    4,200

    Make the boolits soft and it'll work fine I'd...

    Make the boolits soft and it'll work fine I'd imagine. I've shot deer with the same alloy you're using out of a 30-30, and it wasn't great.
  17. Replies
    138
    Views
    33,202

    A Redhawk 45 Colt, loaded hot; or a 4" .40...

    A Redhawk 45 Colt, loaded hot;

    or a 4" .40 S&W. 8 grains of Longshot will get you 1150 FPS in a reasonably sized package
  18. Replies
    0
    Views
    275

    WTS-7mm Remington Magnum Reloading

    I have the following for sale:

    177 Berger Classic Hunter 168 grain .284 bullets. $90 shipped.


    A set of Redding Premium FL dies (j am not certain these have had a round loaded on them), part...
  19. Replies
    18
    Views
    3,887

    I’ve used both Hi Tek and PC. In my...

    I’ve used both Hi Tek and PC.

    In my experience, getting the PC to stick to the bullets in the proper amounts has been tricky at best. I’ve tried varying preheat temps and times, and I either get...
  20. Replies
    73
    Views
    7,061

    OWB at 3:00 IWB at 1:00 or 3:00

    OWB at 3:00
    IWB at 1:00 or 3:00
  21. Replies
    24
    Views
    5,139

    My old man used to have a beretta 92, and I...

    My old man used to have a beretta 92, and I wonder if that thing had any rifling. It would chamber ANYTHING.
  22. Replies
    20
    Views
    1,789

    Lee for me

    Lee for me
  23. Replies
    62
    Views
    10,892

    We buy bullets made from copper and devote the...

    We buy bullets made from copper and devote the massive amounts of time we spent casting doing other gun related stuff.
  24. Replies
    34
    Views
    9,934

    I may have to start to pick up more range lead. I...

    I may have to start to pick up more range lead. I quit for awhile but hospital lead is getting harder to find in my area.
  25. Thread: 550 happiness?

    by HCH
    Replies
    72
    Views
    15,432

    I’d get all the goodies I could with a 650. ...

    I’d get all the goodies I could with a 650.

    The reality is, for the amount I shoot (more than the average cat, as I shoot USPSA and 3gun) I feel like the 550 does a fine job. I load 9mm, 40,...
Results 1 to 25 of 51
Page 1 of 3 1 2 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check