Search:

Looking for a good lever gun smith in southeastern Wisconsin. I have a Winchester 94 AE in 44 Mag that is having some ejector problems. It is extracting the fired cases and then after partial...

Is the 50-50 the only lube you sell that this affects?

The big doe I took last year with the 45acp was also a high double lung like yours. She also ran about a hundred yards at a dead run with almost no evidence that I even hit her until the last 20...

I'm in for 4 molds paid by US postal money order. Please pm me for address to send funds.

Great job on a nice deer. The 44 mag is my favorite rifle for deer hunting. Just gets it done and is what I used for my first self-cast boolit deer. Great memories.

Nice job. That's a nice buck.

Awesome, congratulations. Someday I'll get one with my gp100. Good eating.

The deer ran close to 100 yards. The shot hit high between a few ribs back, angled down and exited lower between two ribs. It then hit the lower part of the shoulder blade. I was hoping for a...

Was hunting at my brother's today. I already harvested a buck from his 15 acres with my bow so he wanted me to take one of the many doe around his place. I was sitting in a stand with max range of...

My Lee 452-230-TC has a meplat of about .3. I would have no hesitation using it for hunting and may this season if the NOE shallow hollow point weighting in at 245 doesn't get the draw.

I have both the 30 Herrett and the 35 Herrett. I cut mine to just a hair long after I run it through the expander with a power miter box and finish trimming like any other cartridge. Saves MUCH...

I dropped off some recycling stuff Saturday and asked about some Linotype. He had a partial bucket with larger single letters I think is monotype. He asked how much I wanted and I said all of it. ...

I have one and it feeds in my Springfield Range Officer.

My Rossi 92 357 would not cycle semi wad cutters from the time I got it. It would do jacketed like the xtp's and if I cycled it hard and fast enough, it would cycle the NOE 180 WFN but no swc's. I...

FIXED!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Not sure what was wrong with it. There weren't shavings or crud under the extractor. There was a slight steel rise from manufacturing that I...

The ejector is also rough probably putting more force on the casing than necessary. The bolt has a small ridge that the ejector it is hanging up on a little. This is really one of the poorest...

It's a 357. At first it launched the spents into orbit. That didn't last. Now it slips over the top of most as it is pulling them from the chamber. I cleaned the chamber and was hoping it had...

Called Rossi for a replacement extractor and the price quoted was $141. They said I needed to order a whole new bolt assembly. Yikes!!!!!! Any alternatives out there?

Thanks for the replies. I tried a sawzall on a bucket of them and it will be pretty easy to cut through the soft brass. I can melt the bulges separately and safely in a pot. I appreciate the...

152404

I should have tried to put up a picture in my first post. The photo is a good rep of all of the valves. It is a fairly large ball at each connection and needs to come off anyways to get...

So I got about a 1000 lbs of lead pipe from an underground contractor. There were also half a dozen pails of shut off valves with lead on one or both sides. It looks like a bulge where the lead...

Thanks Larry. Time to mess around a little.

Larry, did you ever shoot this load with 31.5 grains and if so, what was the psi? How did it do? Thanks.

I have the same one with the slower micro-groove barrel. It slugs for .431. I use both .431 or .432 with no difference in accuracy. I shot 240 xtp's when I first got it. It shot consistent 1 1/2"...

My Winchester Trapper in 44 has the "micro-groove" barrel also with 1 in 38 twist. It is very accurate. Consistently shot 240 xtp's into an 1 1/2" at a hundred. I use cast now and shoot the RCBS...