I have an LCR in 38, bought very shortly after they came out.
Not a bad little gun, trigger is heavy but pretty smooth, makes it take practice to hit a 6" plate at 25yds with any consistency, my...
Type: Posts; User: Beef15
Forum: Cast Boolits
I have an LCR in 38, bought very shortly after they came out.
Not a bad little gun, trigger is heavy but pretty smooth, makes it take practice to hit a 6" plate at 25yds with any consistency, my...
I shoot USPSA Carry Optics. Significantly more accurate with a RDS, speed is about the same, with a slight bias to the RDS, but it took months to get it there.
Best things, in dry fire practice it...
I have no trouble clearing a plate rack at 25yds off hand with more emphasis on speed than accuracy. Never bothered shooting groups. Feed it whatever 9mm I have with me.
Throat is short, 124 HSTs...
Don't think I've been to a match with steel and not been hit by something, rarely draw blood. Angled down, falling, or free swinging it helps, but it's not 100%. I do not play about eyepro.
Full...
Extended release is fantastic, may not cure your problem, certainly not the root but for the cost of a value meal why not try it? Glock OEM hit the edges with some sand paper. Got my last from NDZ.
...
3.0 of Bullseye worked good for me with a bullet that looked just like that one that I used to buy from a commercial caster.
3.2 of Titegroup did also, pretty sure that's over Lyman's data but a...
Forum: Coatings and Alternatives
1st post. Sized .357" after Powder Coating.
Sent from my SM-G360V using Tapatalk
Forum: Coatings and Alternatives
Thanks for the replies.
I guess I'll hone out the sizer a little further. I am hesitant because I believe I will reach a point where I have to load several COALs for different guns, and of course...
Forum: Coatings and Alternatives
Making one's own tools is great if you enjoy it, your specs are very similar to a Lee 38 S&W powder thru expander .3535/.354" cylinder approximately .20" long that I'm running about .25" (including...
Forum: Coatings and Alternatives
I was wondering about thickness of coating. If .0005/.00075" was sufficient? Any good way of bumping it up without two coats?
Using ASBB DT with HF red.
No BBs with the grey gives full coverage.
...
Forum: Coatings and Alternatives
I am shooting them sized .357".
I have tried them at smaller sizes. I have had commercial coated cast bullets work without leading in this gun at smaller sizes.
Current and pictured powder is...
Forum: Coatings and Alternatives
The .357"s are what I am currently loading, may be slightly less leading than when I tried smaller.
Same alloy as the traditional lubed bullet I run at .358".
Was doing 20 minutes total then...
Forum: Coatings and Alternatives
Anyone else have any thoughts?
Tried .355 because that's what my .356 Lee sizer left them.
.356 because while honing it out I figured what's the harm?
Doesn't seem like .358 or even the...
Forum: Coatings and Alternatives
Hello, looking for a little help with leading, in a 9mm no less :???:.
Facts
Gun: Gen 3 Glock 17 OEM barrel
Bore: .3555
Previous success: .355 & .356 commercial HiTek, .358 lubed COWW water...
Forum: Cast Boolits
I would use the Power Pistol. I had good results with the Lee 120TC and that powder, don't remember the charge.
What will likely be a challenge for you is expanding the neck for and/or seating a...
You could just drive the sizing ring out with a brass drift or wooden dowel. It's just pressed in. Can be taken in and out a few times and still hold.
Sent from my SM-G360V using Tapatalk
My Shield seems to like the NOE 358133RN pushed by 3.5gr of Bullseye, I think OAL was 1.13.
Sent from my SM-G360V using Tapatalk
Bought Shield 9 back in May, submitted for rebate same day, received this week.
Gun is good, looked at a thumb safety model, too small and stiff. Trigger is heavy and long, fairly smooth though,...
Not much help, they will get harder to an extent as they sit after baking. Tumbling is often a side effect of severe leading. Curious to see what it is.
Sent from my SM-G360V using Tapatalk
Forum: Coatings and Alternatives
I flip mine into a wire basket over a sheet of foil, dump back in bowl. With ASBBs I pick them, but only because I haven't bought a colendar and my wire is too tight a mesh.
Sent from my SM-G360V...
Forum: Cast Boolits
This. Not that I have an abundance, just a couple Glock's, a Shield, a DB9, and M&P357Sig. And ran them through a friend's RIA 9mm 1911.
If I have issues with plunking 9/10 it's the case mouth...
Forum: Reloading Equipment
I load it all.
I've heard stories of the stepped stuff separating, haven't experienced it yet, have loaded lots of it.
S&B brass washed steel, load it right up too.
SDs might be a little on...
Forum: Cast Boolits
Really is a great bullet. I'm lobbing solids for USPSA, 2.7gr of RedDot @ 1.135 makes minor, groups around 3.5" at 25yds, easy recoil. Had to seat about a hundreth deeper for PC and accuracy...
Forum: Coatings and Alternatives
I shoot a G17 in competition minor PF, factory barrel, slugged same as yours .3555.
HT .355, .356, .357 all shot fine, no leading, routinely went 1500-2000 rounds between cleaning. TG or Bullseye....
Forum: Coatings and Alternatives
My new .356 sizes PC'd COWW to .355, they seem to shoot fine.
My .401 sizes the same alloy to .401 and the little inaccurate 5 blinks.
I do have some 1000 and 1500 grit around here, now I have to...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |