Search:

Got the concrete poured Friday evening for the floor to enclose an open bay for my woodworking shop. Getting all of the woodworking tools and lumber out will really free up space for the...

Loaded 300 40's. Now I have 700 loaded rounds. That will do for a few matches. Of course, if we don't get to more matches, it will last much longer. I also finally finished the cart for my new...

Well, if you decide you want to build those Ram Chuckers I would probably be your first customer.

Started to load some 45 acp. Did a couple and then the primer feed wouldn't do all the way, so I tore it apart and realigned the machine and now it seems ready to go. I hope so. Will find out...

Tightened the set screw on the side. We will see how that works.

Loaded a few 10 mm rounds to test the new powder funnel from Mr. Bullet Feeder I put in yesterday. Seems to work good. Then I changed the press over to 45 acp so I can load some for my wife. ...

Since I have had some problems sizing previously, I tried something new today. I sprayed about 1/3 of the bullets with One Shot case lube and then would size one sprayed bullet and then two non...

I will have to check on that. I didn't notice a copper wire between the sprue plate screw and the set screw and check if the set screw on the side is tight. Thanks

Powdercoated 45 acp and 40 s&w today and used silicon mats to cook on. My wife was kind enough to buy me one and since my cookie sheets are small I was able to cut it in two and use both sheets. ...

Powder coated a bunch of 45 acp and 40 s&w.

That is amazing! I wish I had the ability to make such things. I would love to have one of those.

Used the moulds today and they worked good. I am pleased with that. One of them I can't keep the sprue plate as tight as I would like. I tighten the screw but it just loosens up right away. Is...

Well I used non abrasive Scotch Brite pads and did not do a lot with them and nothing in the cavities. The moulds look much better, but we will see when I use them again.

Life got in my way for a while. Finally got out to the shop and took the moulds out to try to clean off the lead. I was skeptical that I could do it which is maybe part of the reason to put it off....

I have only Delta Elites, but really like them. They are fun to shoot with that extra boost they provide. However, I also like a lot of other cartridges. Since I shoot a lot of semi autos, chasing...

Thanks for the suggestions. I am going out of town for a 3 gun shoot in a couple of days and have things that have to get done before them so I may not get to it until after I come back. However,...

And I need help! I was casting today and on my third pot of 45 acp I noticed there was a small crack between the mould sides. I then looked and the bullets had, for lack of better terms, wings on...

Loaded up 30+ 10 mm rounds with 6.8 grains of Power Pistol to be chronoed when we get a decent day. 7.3 grains averaged about 1150 fps. Want to try to get down some for a fun load.

I spent the last two days building a shelf unit to hold ammo, so spent time cleaning the reloading room. Sawdust everywhere!

Congratulations from another fairly new caster!

I bought a new Talo gun, at least it has the T at the end of the serial number. I looked for an older one a while back and the prices were outrageous. I found this one at a somewhat reasonable...

I usually scour ebay until I find some at a good price with free shipping. It is amazing the difference in prices charged.

I have one die with a bullet still stuck in it, so I will try melting the lead out.

Thanks for all the ideas. I will try to polish the die, but I am not sure I am capable of doing that correctly. I will also lower the temperature of the oven or cook for less time and see if that...

I always size before and after coating. It is after coating that I have the problems. I am coating at 400 degrees for 20 minutes. Does this sound right? I have an oven thermometer in the oven...