Just saw this thread. Outstanding job!!
Type: Posts; User: PTCSmith
Forum: Gunsmithing Tips & Tricks
Just saw this thread. Outstanding job!!
Forum: "The Barrel Works"
Brownells offers short-chambered barrels in 6.5, .308, 25-06, and 30-06 for $125. If money is short, this is the way to go. They usually shoot fine for hunting.
A take-off barrel was removed for...
Forum: Gunsmithing Tips & Tricks
We had our students tape one of these to the inside lid of their toolbox.
https://live.staticflickr.com/65535/52470926873_bb77cd6836_b.jpgLathe Settings by jakefromclemson, on Flickr
Forum: Gunsmithing Tips & Tricks
i'll second Keith Rice. No website, but Keith normally answers the phone. Generally 30 days to complete the work and return the reamer.
Forum: Gunsmithing Tips & Tricks
This fellow was trained at the old Colt factory. He has a fairly extensive supply of obsolete parts as well as the knowledge to use them.
Spartan FA Company, LLC
1884 Birchwood Dr, OKEMOS, MI...
Forum: Gunsmithing Tips & Tricks
Replace the trigger assembly. $50 - 80 on ebay
Forum: Gunsmithing Tips & Tricks
A Yugo Mauser (M48 or 24/47) calls for an extractor cut. I also add the safety breech that was part of the original design. Failure to make the extractor cut may make the bolt impossible to close....
Forum: Gunsmithing Tips & Tricks
This one is made from a piece of Walnut. I just drilled holes to match the handles of what I wanted to keep in the block.
https://live.staticflickr.com/65535/51858238706_53aef53099_b.jpgFile Rack...
Forum: "The Barrel Works"
Yup! There are a blue million 742 single shots out there. I have one in my shop now. The forend screw is so rusted that I can't remove it. Soaking in Kroil now for the weekend.
Forum: Gunsmithing Tips & Tricks
You can cut them from Threaded Lamp Rod, and they work just as well as anything else. ...
Forum: Gunsmithing Tips & Tricks
I wait until I have an order to make and then call in the order rather than doing it on the internet. I tell the order taker that I need replacements for bits no. 210-2 and 240-3 or whatever, and...
Forum: Gunsmithing Tips & Tricks
What is the advantage from making this modification vs. buying additional Handi-rifle barrels?
Forum: Gunsmithing Tips & Tricks
I use a 2' x 3' piece of beige carpet from a cheap store near me called "Ollies." The carpet has a low pile height and keeps pins and screws from rolling off the bench. When it gets so soiled that...
Forum: Gunsmithing Tips & Tricks
You tend to collect a few cutoffs over time. The T-Handle on top of the pile is one of the better uses that I have found. The barrel section is now a handle for a rimfire reamer holder.
Bill...
Forum: Gunsmithing Tips & Tricks
I'm getting them from Jim Wisner.
https://farm8.staticflickr.com/7808/47247987292_88afcd0eec_z.jpgStraddle Floorplate by William Jacobs, on Flickr
Bill Jacobs
Forum: Gunsmithing Tips & Tricks
I like the spray stuff (AcraRelease?) that Brownells sells. I have also had great results with Hornady One Shot Case Lube. A spray release agent is so easy to use. As a previous poster said,...
Forum: Gunsmithing Tips & Tricks
It isn't elegant, but I use this shop-made jig for jeweling. I align it with the mill table and clamp it down, then I advance the table using the hand crank 0.1 inches at a time (or 0.2 if I want to...
Forum: "The Barrel Works"
It is easily a half-day's work to set up the barrel and taper it. You would be better off buying a new barrel of the contour that you want.
Bill Jacobs
Forum: "The Barrel Works"
Labor would run around $600 plus the cost of an oversized recoil lug.
Bill Jacobs
Forum: Gunsmithing Tips & Tricks
I do Mausers regularly, and I would advise that you get the receiver and bolt to work with. You can measure the distance from the primary torque shoulder to the bolt face to see how much the gauge...
Forum: Gunsmithing Tips & Tricks
This is good advice. The plastic follower tends to stick in the tube. Replace it with an aluminum of stainless steel follower from Brownells.
Bill Jacobs
Forum: Gunsmithing Tips & Tricks
White Rock is my go-to reamer place. I'm not up to the time and effort that it takes to advertise, package, and sell a reamer after I use it. If I plan to cut more than one chamber, I will buy a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |