I'll take #8, Gripper grips. PM sent.
Type: Posts; User: Rich/WIS
Forum: Swappin & Sellin
I'll take #8, Gripper grips. PM sent.
Forum: Rimfire Area
Found a later model left hand for my grandson when he gets bigger. Really accurate. There was someone selling replacement springs that would reduce the trigger pull and think it was Rimfire Central...
Forum: Rimfire Area
Number of posts on various forums about using epoxy to attach the base to the receiver, people reported it worked and held up well.
Forum: Military Rifles
A bevel on the striker may be all you need to mate to the bevel on the safety. If you have a GI trigger on hand swap it with the commercial trigger and see if it does the same thing. If not the...
Forum: Completed Deals
Years ago the nut that holds the sizing die on my LAM I stripped and RCBS had me send it back. Before shipping it I stripped all the parts off and sent the body to RCBS. They did not repair it and...
Rem, Peters, WRA all loaded soft point hunting ammo for the Krag. Following WWI most of the Krags were sold off cheap and were commonly used for hunting. Some, like the carbines, were used as is...
Forum: Military Rifles
The Krag I owned had the same issue. Didn't use the O ring but simply fire formed and then neck sized only. Doing it that way there were no further issues.
Forum: Our Town
My safe is int 500# range and found it was easy to move, called the local movers and they did it. When I moved from WI to KY the moving company moved it. They had me leave the door open and removed...
Forum: Casting Equipment
The Schupter looks interesting but is intended for black powder bullets right now. Max pot temp in 750 so just a little hotter than a lot of molds like to be run and apparently uses proprietary...
Forum: Military Rifles
After you bevel the notches engage the safety, pull and release the trigger and then move the safety to the fire position. If the striker falls you need to start replacing parts.
Forum: Our Town
When I retired from the Army in 92 was stationed at Ft McCoy in WI. Moved there in 91 and wife and I liked the area so bought an old farm with 60 acres, a big old farm house (3200 sqft) and a barn,...
Forum: Swappin & Sellin
Springfield made a lot of stuff, what in particular is he looking for.
Forum: Casting Equipment
IIRC the end of the rod on the SAECO 24 is not tapered like a pencil, it is flat and square on the end. As someone else said pictures would hel a lot to diagnose the problem.
Forum: Our Town
Never really smoked cigs, doubt if I've hadmore than a dozen in my life. Did smoke cigars now and then, haven't had one in years. I am however a dedicated pipe smoker, started in my early twenties...
Forum: Cast Boolits
If it doesn't stick out the front of the cylinder it is not too long. The OAL measurement is meant for 1911 and similar autos.
Forum: Our Town
The key to good insulating qualities is the glass. Spent several years as maintenance supervisor in a factory that made the insulated glass for window makers like Pella and Anderson. The technology...
Forum: Cast Boolits
Might want to slug your barrel, last 9mm I had was an mid 80's CZ 75 that slugged .357.
My Lee Auto Prime II specifies what primers to use, and I always use CCI as they are approved for use. Fiocchi primers were not around when the tool was being made so are not referenced in the...
Forum: Cast Boolits
The Cast Bullet book is a wealth of solidly researched info that has served me well since I purchased it when it first published. Most of the info was originally published the American Rifleman back...
If the labeling on the bottom is DEN then was ammo made at the Denver Colorado Ordnance plant, in production from 10/41 thru 7/44. Made 30/06 of all types. The 03 ands 03/A3 Springfield was still...
What are you going to load, have a full bag of their T-42 wads used for heavy loads with Blue Dot. If you can use them just pay postage on a MFRB.
Forum: Swappin & Sellin
Sometimes someone on the CMP forums is restoring a Sporter and selling the sporter stock. Might check there or possibly E-bay or the Krag Forum.
Forum: Casting Equipment
Think he means area between the rod and the side of the pot, I'm like Winger Ed and use an old screwdriver. Anything long and thin will work. When I'm done casting and have drained the pot there is...
Forum: Our Town
Link still required logging in, so gave up and re-registered.
Forum: Our Town
Anyone here on the RugerForum.com? Was on there until a few days ago when my computer had a brain fart and had to reload all my various forums sites. All went well except for the Ruger site. ...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |