i recently bought one of the slovenians molds a 525 grain slug.
looking for power to be used, amount of powder, and wad.
any help appreciated.
rw
Type: Posts; User: gumpy
i recently bought one of the slovenians molds a 525 grain slug.
looking for power to be used, amount of powder, and wad.
any help appreciated.
rw
Forum: Group Buy Archives
Hihec, recieved shipping notice for 130grain and i paid with pay pal. But i made mistake on original order as above. wanted the 125grain hp version too. I indicated this on original order without...
Forum: Group Buy Archives
rwweddleATqDOTcom .......................130gr without lube grooves with BB one of these, and in addition one of the hollowpoings without lube groves with BB
Forum: Cast Boolits
i have been having a running dialogue with a guy i know on lead bullets. I recieved this today in response to an email stating i was not gettin leading at higher velocities, if the bullets matched...
Forum: Group Buy Archives
I just caught the change, this is to inform i still want to be in:
gumpy, rwweddleATq.com 1-4cavity all pins.
ron
Forum: Group Buy Archives
sign me up for option 1, 3, 4, 5.
rwweddle at q dot com
this is an update
Forum: Group Buy Archives
put me in for a four cavity mould, with blank, round, and penta pins,
email address as follows:
rwweddleATqDOTcom
Forum: Group Buy Archives
include me in:
rwweddleATq.com
4cavity, blank, small, large, and penta pins
Forum: Cast Boolits
i have a certain amount of powder from the 60's in the original cans, and primers from that period. One of the things i haven't gotten around to is loading some .45colt with that old unique, and...
Forum: Cast Boolits
a few years ago there was a large quanity of french m2 ball ammo obtained. This was headstamped in the 50's and stored in a garage in phoenix, not air conditioned from that time frame until a couple...
Forum: Cast Boolits
I have a marlin in .44mag and i did slug the barrel and found that .4315 diameter. The solution was to order some gas checked montana bullets that were over size to that and they worked just fine. ...
Forum: Group Buy Archives
i was on the original list for this mould, but still haven't seen any email to send money or anything else for that matter. Some months ago i was notified after sending an email it was going to be...
Forum: Group Buy Archives
any news on the cramer mould for .41?
i show on the list but have heard nothing as to billing/invoice/etc.
Forum: Cast Boolits
Was using the following load today.
A montana bullets 240 grain S.W.C. gas checked with a heat treated bullet of lyman No 2 to a BHN hardness of 22. This is a N.E.I. mould.
They WERE SIZED to .432...
Forum: Cast Boolits
am I missing something? The most I can seem to find in a sizing die is .431, haven't been able to catch a .432
Forum: Cast Boolits
the inside of my forcing cone was a lot rougher looking than i expected. I am going to have to compare that to some of my older smiths out or curiousity. I don't have a guage to check constriction...
Forum: Cast Boolits
while this may not be the best way to do it, working with what i had, i shoved a 30.06 casing in the front of the cyclinder, marked it and measured. I came out with .429
Later to day I am going to...
Forum: Cast Boolits
i recently slugged a marlin 1894 barrel and no surprise it came out at a little over .431
I have ordered some cast bullets sized at .432 to fit the rifle. The question i have is using the same...
Forum: Group Buy Archives
if i am not to late for this buy put me in for the following:
One 4cavity soldi fp mold
one 4 cavity cramer hp mold
for the hollowpoint, if the extra pins are to cast a penta hollowpoint, toss in...
Forum: Group Buy Archives
add me to the buy, one mould and both sets of pins.
ron
rwweddle at q dot com
Forum: Cast Boolits
recently i obtained some reloads from the estate of a deceased friend loaded as follows:
.45acp
lyman orange magic lube
200gr swc r-p brass
4.6 grains bullseye
cci primer
SIZED TO .454
The...
Forum: Cast Boolits
a friend lent me a mould that i have since given back. Think from memory it was a r.c.b.s. mould. In any case, the stated weight was 185 grain, and with wheel weights they threw to around 194...
Forum: Cast Boolits
having recently fallen in love, again, this time with the .41magnum i had to comment on the above mould. I just got through throwing a bunch of 185grainers from an old lyman mould i borrowed for...
Forum: Casting Equipment
I have the 450 of my bench today, am in the process of degooking it from accumulated years of lube. Then i am going to remount it on the heating element using your suggestion. thank you. ron
Forum: Casting Equipment
i have a 450 mounted on a heatin element. Was using a blue hard lube and switched to lyman regular lube. I noticed that the blue lube was squeesing out of the bottom of the 450, and the lyman is...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |