Lee PrecisionWidenersReloading EverythingRotoMetals2
Load DataTitan ReloadingInline FabricationMidSouth Shooters Supply
Repackbox

Search:

Type: Posts; User: jrfixer

Results 1 to 20 of 21

Search: Search took 0.00 seconds.

  1. I have found a Saeco mold #221 62grain sized to...

    I have found a Saeco mold #221 62grain sized to .225 with gas check and traditional Saeco lube and a COAL of 2.160 over 19 grains of AA2230 are tack drivers out of my RRA 16" 1 in 9 twist. They...
  2. My 550 with new UFO leds installed. Where were...

    My 550 with new UFO leds installed. Where were these 10 years ago!


    209262
  3. Working the 9mm mold. 207452

    Working the 9mm mold.

    207452
  4. Replies
    38
    Views
    9,268

    Forum: Boolit Lube !

    Beagle your mold and size to .358 and your...

    Beagle your mold and size to .358 and your problem will be gone. My Sig 239 will eat these and drive tacks at 20yard all day long.
    ...
  5. I rented a truck with a power lift to get them...

    I rented a truck with a power lift to get them home. I have a small pallet jack that I used to move them along the wall and stacked them with an engine hoist.

    Last summer I sold two of them to a...
  6. Replies
    273
    Views
    105,618

    Poll: Opening day 11/02/1983 on dirt bike trails I had...

    Opening day 11/02/1983 on dirt bike trails I had seen sign on that summer. Took a stand on the down wind edge of an open area that was fogged in. As the fog burnt off - boom. 12ga slug; one shot. ...
  7. Big blocks of 95/5 make great many little boolits...

    Big blocks of 95/5 make great many little boolits :grin:

    Each block is ~500 lbs

    205695
  8. Replies
    9
    Views
    1,659

    Forum: Cast Boolits

    Just loaded 3 groups of 4: Coal ~ 2.720" ...

    Just loaded 3 groups of 4:

    Coal ~ 2.720"

    Powder is imr4895

    30gr, 33gr and 35grs

    As soon as it is above 0 degrees around here ill post the results..LOL
  9. Replies
    9
    Views
    1,659

    Forum: Cast Boolits

    It is casting season here in New England, so here...

    It is casting season here in New England, so here is a pile from my 311365. They are 205 grains with a Cu GC.

    93986
  10. Thread: Cast in 45ACP

    by jrfixer
    Replies
    22
    Views
    2,923

    Forum: Our Town

    Great minds think alike :mrgreen: JR

    Great minds think alike :mrgreen:

    JR
  11. Thread: Cast in 45ACP

    by jrfixer
    Replies
    22
    Views
    2,923

    Forum: Our Town

    I have been using 4.9Gr of Unique with a ~230Gr...

    I have been using 4.9Gr of Unique with a ~230Gr bullet and OAL of ~1.210 for punching paper with my P220R3-EQ.

    Here are a few pictures of my latest batch :mrgreen:
    ...
  12. Replies
    21
    Views
    3,221

    Forum: Cast Boolits

    I found with the 9mm I size to .358 for my Sig...

    I found with the 9mm I size to .358 for my Sig P239. In order to do this using my Lee 6 cav mould I had to open it up with valve compound and beagaled .002 with copper tape. They are lube with a mix...
  13. Forum: Cast Boolits

    I had the same problem and found that a demo...

    I had the same problem and found that a demo hammer was the way to go. Now I have 9 blocks that are around 500 lbs each so the ROI on the demo hammer was easily justified. I bought a Bosh for $200 at...
  14. Replies
    37
    Views
    4,801

    Forum: Cast Boolits

    I had the same problem with my 500lb blocks. I...

    I had the same problem with my 500lb blocks. I found that a demo hammer was the best choice. See this link http://castboolits.gunloads.com/showthread.php?t=16655

    I bought a Bosh Bulldog from Home...
  15. Replies
    22
    Views
    3,378

    Forum: Cast Boolits

    I had already tried using heat with map gas and...

    I had already tried using heat with map gas and my soldering torch. I found that the block was so much of a heat sink that it hardly melted anything. I tought about moving to the oxy/ace which would...
  16. Replies
    22
    Views
    3,378

    Forum: Cast Boolits

    Yep, I used an engine hoist to move them from the...

    Yep, I used an engine hoist to move them from the folklift to the pallets.

    Wire Nut, you might be on to something there. I never thought about a power wood splitter. That would definitly be...
  17. Replies
    22
    Views
    3,378

    Forum: Cast Boolits

    Yes, They are counter weights from a few machines...

    Yes, They are counter weights from a few machines we scrapped.

    I have already tried a sawsall with a few different blades, and it didn't work to well. I found the demo hammer worked pretty...
  18. Replies
    22
    Views
    3,378

    Forum: Cast Boolits

    Now I need a good Demolition Hammer

    Hows this for a supply of lead ?

    http://home.comcast.net/~jrfixer/gun/lead.jpg

    The only problem is moving them (500lbs each) and chopping them up to usable pieces. If figure this should keep...
  19. Replies
    13
    Views
    6,234

    Forum: Cast Boolits

    Hi everyone - Long time lurker first time poster...

    Hi everyone - Long time lurker first time poster :D

    I have the Lee TL365-124-2R mold. I have been loading them in 9mm for my Sig P239. I TL them lightly with LLA and then run them thru the Lee...
  20. Replies
    14
    Views
    2,780

    Forum: Cast Boolits

    I just started casting and found my first...

    I just started casting and found my first challenge was cutting up the 400lb lead counter weight I had. At first I tried to use a map gas, but the block was to much of a heat sink to make this worth...
Results 1 to 20 of 21
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check