Search:

So here is a question, my cast loads will not feed well in my 300AAC, what OAL are you guys using? also, I haven't been able to find good load data for the LilGun powder that I bought. This catridge...

Sorry for late response, just moved to FL, DKF, you think a flat nose would be better than a pointed? I really just want a reliable mould for my .223, 5+ cavity... shooting 300yrds or less. I know my...

I put this thread on here so people would see it, and comment on any design recommendations, such as what 45 2.1 said. I also posted this in the Group Buy Section.

Attached is a mold design from NOE Molds, for a 5 cavity SP Pointed Tip .224 65gr boolit. With Hi-tek lube should shoot perfectly! Add your name and email if you want a set. When I get 15 names I...

I don't know about the "kool" effect, nor do I care. I know that with the new hi-tek lubricant, you no longer need to buy, or seat gas checks on rifle rounds. As far as long range effectiveness, I...

$99 for a 5 cavity mold.

Attached is a mold design from NOE Molds, for a 5 cavity SP Pointed Tip .224 65gr boolit. With Hi-tek lube should shoot perfectly! need 15 buyers to get the price. 80696 Add your name and email if...

So you guys are buying the .225 and sizing down to .224? I see them on his sight.. What type of sizing die though? My lee .308 sizer does a number on my .309 boolits on occasion

Looking for a good mold to cast for my AR. Missed the 22 GB earlier this year. Any recommendations or suggestions??

Gotcha, do you know if there is anyway to take the chamber down a bit? IE gunsmith filing... Looks like I'll be saving all my match brass for the Rem700!

So I got a CETME, semi-auto .308 rifle. Most people know them as H&K G3, (clones) I took it to the range today and like any diligent reloader, went and collected my brass. Lo and behold this is what...

I've started casting .309 170gr boolits for my .308, I am getting a lot of marblization in my boolits. Will cast perfect in .452, then like **** in my rifle moulds.. temp issue? Mould temp issue??...

After I coat about 100 boolits with the hi tek, that come out perfectly pretty green, the second batch i make is all gummy and sticky and don't want to dry nice and even like the first batch... the...

Bought a black and decker toaster over an walmart for 29 bucks.. easy removable rack, and will go up to 450 deg no prob. Just did my first back. Tip for other newbies... LET LUBE DRY ALL THE WAY...

Very Very good point. I have the Lee .452 cavity mold, and they will NOT chamber in my 1911, the .451 sizing die is already in the mail!

You showed a pic of the mixing stuff... but what are they? Can't really tell from the pic. Also, what do you use to bake? You said outside, I was thinking reg oven before you said that. And if you...

Problem solved! I played around with the case flaring die, and adjusted the boolit seating/crimping die. Ordered the tapered crimp die today, will push them through that also just to double tap. But...

Cummins, the sizing die decapper pin goes all the way into the casing. The case goes flush with die, cannot. Seat anymore than it has. I suppse I could replace the decapper pin with one that is .457,...

Green lizard, flare with??

Problems... So I lubed these last night, and let them sit until around 1800 after I got off work. Was conducting my "test seating" to ensure bullet seat depth was good for OAL/chambering etc... I put...

Problems... So I lubed these last night, and let them sit until around 1800 after I got off work. Was conducting my "test seating" to ensure bullet seat depth was good for OAL/chambering etc... I put...

Epiphony! Everyone complains about their bullet seating die being fouled up with lube.. if I literally freeze my already lubed boolits, right before I load them, wouldn't that cause the lube to not...

Firebricker, after I load these tomorrow I'll do a few test cast/lubes and stick in fridge. I'll let you know. might be different after I make the 45/45/10 lube tomorrow as well.

prsman, damn.... guess ill have to melt them back in,, :kidding:

Here is my first cast! 6 cavity Lee .452 mold, pure COWW alloy, sprayed mold with the easy out stuff, it worked AWESOME! I tumble lubed them and set them on wax paper to dry overnight. I live in NC,...