I made some progress, but still not consistent when there is a lot of brass in the cup. I need to mount the feeder to keep the angle consistent mostly. I also still have some brass getting caught...
Type: Posts; User: dwwright
Forum: 3D PRINTED RELATED ITEMS
I made some progress, but still not consistent when there is a lot of brass in the cup. I need to mount the feeder to keep the angle consistent mostly. I also still have some brass getting caught...
Forum: 3D PRINTED RELATED ITEMS
I was able to get a prototype printed tonight and mess with it a bit. I've got some modifications to do/try, but found it worked fine in small batches. The chrome plated brass is 9mm, the other is...
Forum: 3D PRINTED RELATED ITEMS
It's still in design, but basically I'm creating a new base plate with slots for each size (9x17, 9x18, 9x19) with a step for each to ride and hopefully tip off into the correct slot in the base....
Forum: 3D PRINTED RELATED ITEMS
I'm working on a plate design to sort .380 ACP, Makarov, and 9mm cases from one another based on case length. Hopefully will have something posted up this weekend if anyone is interested.
Forum: 3D PRINTED RELATED ITEMS
Those look good! Saved for later.
Forum: 3D PRINTED RELATED ITEMS
I believe I am using a spring from my 3d printer bed, maybe with a coil or so cut off.
Forum: 3D PRINTED RELATED ITEMS
I'm printing the parts for Harri678's case collator conversion using a JYG-370 10rpm motor. I'm assembling an entire new bullet feeder for this project. Here are a few pics of the coupler I used for...
Forum: 3D PRINTED RELATED ITEMS
They actually measure 9mm in diameter and fit a 6mm shaft. The coupler is about 20mm long. You'll need to order some m3 set screws for the shaft side (some short 1.5mm - 2mm ones), the other you can...
Forum: 3D PRINTED RELATED ITEMS
I'll have to measure mine tomorrow if I get up to the shop, but the walls are about 2mm on these, so comes out to about 10mm......
Forum: 3D PRINTED RELATED ITEMS
Ok, thanks. I'm still chugging along on this. I did end up ordering the springs for MBF, much more flexible than the spring benders and I'll need the extra length that they can provide too. Tonight I...
Forum: 3D PRINTED RELATED ITEMS
I'm curious about the spring connectors to the main body, there are large and small ones. I assume the sizes listed are for the diameter of the bullet. Also noted on the drop tubes. Question is, does...
Forum: 3D PRINTED RELATED ITEMS
I got mine running tonight, but obviously I need to figure out the right ramp plate to print for .223. I was able to hold one of the two I printed in place for a bit and get some successful flips on...
Forum: 3D PRINTED RELATED ITEMS
No worries, I ordered a couple of the couplers below to try, looks like the threaded holes go through already upon closer inspection, so just need to remove the head of an m3 screw that is long...
Forum: 3D PRINTED RELATED ITEMS
So I'm planning to use the JGY370 motor, but after installing it to the main body it's obvious that the shaft is way shorter and doesn't have the "T" needed to spin the collator plate. How have...
Forum: 3D PRINTED RELATED ITEMS
Both finished up overnight, I went with a .223 bullet collator since that is what my current casing collator is setup for.
220489 220490
The back of the main body was only peeled from the bed...
Forum: 3D PRINTED RELATED ITEMS
Thank you to AmmoMike83 and other contributors that have made this available, new build going on here. I've got two AM8 printers going one with the main body and another with the collator. My older...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |