Anything worth having is worth waiting for. Thanks John Taylor
Type: Posts; User: kysunfish
Forum: "The Barrel Works"
Anything worth having is worth waiting for. Thanks John Taylor
Forum: "The Barrel Works"
I could ship it to someone who has a C&R with the original barrel screwed in. I have a Barrel vise and receiver wrench. I have a valid C&R
Forum: "The Barrel Works"
If they have a 4 jaw chuck and steady rest I can pay the bill. I'm not interested in a slop job
Forum: "The Barrel Works"
I could use a referral from someone who knows good work when they see it. I have a Lothar Walther stepped barrel for a K98 with .264 bore that is not chambered. It is threaded and crowned. I would...
Forum: Vintage Ammo
I have encountered two types of Turk 8mm over the years. Light ball and heavy ball. The light stuff works pretty good in long barreled bolt action 98's like the model 38 and 98/22 Turkey used. I...
Forum: Reloading Equipment
Those 7.7 Arisaki actions are strong. You can fire just about anything it will close on and neck size from there. 303 Data will work all day long
Forum: Completed Deals
(Thank you) I'll have to look at the part numbers and see because it does make the odds much better of finding one
Forum: Reloading Equipment
The 0 ought bar is for red dot 3 Drams Trap load.
Forum: Completed Deals
I've decided to get my old 4X4 Auto up and running. I watched an older Youtube video and learned that RCBS actually produced these but when I contacted them I learned they were no longer available....
Forum: Completed Deals
If for any reason this becomes available please PM me
Forum: Single Shot Guns
I'd buy one tomorrow if they came in 454/45 Colt . You would think with as many offerings that Henry has in 45 Colt repeaters that they would consider it and the .357/38.
Staying to the light strikes thing I will say that the piece of glass on my bench has helped me detect a lot of high primers over the years.
Well I bought me a 4.2 convertible 45ACP/45Colt and need some sound advice on what to feed it. There is some question as far as sizing goes and I really don't want to start reaming the cylinder on a...
It wont be difficult to achieve those velocities. I would go with gas checks and rifle powder. 4350 or 2700 is my go to and seems to work right around starting loads give or take. Most 8mm's like the...
Forum: Gunsmithing Tips & Tricks
Left hand bits are very good stuff. The part about taking a piece of hot brazing rod to the head is very good advice. I have taken a electric screwdriver or drill and chucked a stiff piece of a hat...
Forum: Gunsmithing Tips & Tricks
That's a first. I've never seen someone use a cross pin for take up. You need something that you can adjust.
Forum: Gunsmithing Tips & Tricks
It's the cocking piece (to short). The sear and trigger look OK but all this must work together. I take it either doesn't stand cocked or fires when closing the bolt. When doing a safety check after...
Forum: CB Loads / Military Rifles
As a young man I switched powder bottles on a Mec 600 jr. It had the red dot bar in it for trap loads and you guessed it Alcan 5. Before I stopped shooting them it split the forearm on a nice old...
Forum: CB Loads / Military Rifles
My RCBS Trim/Form die is the greatest. Pull it down then whack it off in one lick with hack saw. A VLD chamfer tool is helpful
Forum: CB Loads / Military Rifles
Well it looks like I should by a lee and the NOE spire point mold. I need to slug several of them and see where this is going size wise. Thanks to all for the advice.
Forum: CB Loads / Military Rifles
I have over a dozen K98K's that I shoot. I have a 5 gallon bucket of chilled shot, some hard ingots and several very large heavy rolls of 55/45 solder. I bought some 174 gr GCRN that I tried with 18...
Forum: CB Loads / Military Rifles
I want to buy me a mold and some Gas checks and perhaps get someone to make me about a thousand on the half's. I have a bunch of lead and solder that I could roll into the deal and really not in a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |