I dug thru my fishing weights until I found one larger than the muzzle. Put an oiled patch down the barrel, started the weight into the muzzle w/ a hammer handle. I used a short section of dowel to...
Type: Posts; User: Bill8914
Forum: Cast Boolits
I dug thru my fishing weights until I found one larger than the muzzle. Put an oiled patch down the barrel, started the weight into the muzzle w/ a hammer handle. I used a short section of dowel to...
Forum: Cast Boolits
Slugged a couple of barrels today and both came out at .308. Started looking at molds and darn. Molds are in the same category as primers it seems.
Where are you folks finding them?
Forum: Casting Equipment
Found that damn hammer. It was in the drawer marked "hammers".
Forum: Casting Equipment
I KNOW I have a small brass& leather headed hammer. I know it is out there. Spent 2 1/2 hours looking for it today. Gave up and used a ball pein gently. No doubt the next time I need a ball pein it...
Forum: Cast Boolits
I managed to destroy a RCBS die today. Got a case stuck in it, ripped the base off trying to undo the mistake, don't have a puller but in my all knowing of all things mind decided "aw I can get that...
Forum: Lead and Lead Alloys
Well anhydrous is still borax, but it contains no water and is crystalline. It will clean mill scale off steel when it is applied as steel is heated to a dull red and then heated further up to forge...
Forum: Casting Equipment
Mal I have a small brake for sheet metal. First time I have used it in a long time.
Forum: Lead and Lead Alloys
Not sure where to put this question so redirect me to another area if needed. I have a LOT if anhydrous borax left from the days I made damascus knives. Is anyone using this to flux your lead? If so...
Forum: Coatings and Alternatives
Practically all powder calls for a 400 degree heat. That is the object heat not air. Once the bullet or whatever you are coating comes up to heat that is when the time at temperature starts.
Forum: Casting Equipment
I got a new Arsenal mold for .225. Of course it would not fit in the guides that are standard for the Lyman Mag 25 pot.
[smilie=b:
So I fabbed one up that should work well w/ the mold & thought you...
Forum: Casting Equipment
When I retired I would spend 6-8 hrs a day in my shop. As time has progressed through the years the shop time has crept down. When I go out the door to the shop one of these days I will meet myself...
Forum: Casting Equipment
Guys I am starting all over again after many years (50 or so) not casting anything. Many years ago a marriage gone really bad & her dad being the county sheriff prompted me leaving in the middle of...
Forum: Casting Equipment
They advertise medication for short term memory improvement. Now if I could just remember the name of that stuff.
Forum: Casting Equipment
Got a new shiny good smelling 5 cavity mold (.225) from Arsenal molds last week. Really nice looking w/o any chatter marks or tooling marks of any kind in the cavitys. Went to the shop today to...
Forum: Casting Equipment
I have purchased Lyman equipment for 60 years or so. I just got one of their Mag 25 bottom pour pots and they are slipping in quality. The limit screw is bent and will not stop the shut off rod. The...
Forum: Testing Area
Been trying to get registered and finally gave up and started over w/ a new user name. Lets see if this works!
Yay it worked - you guys are in trouble now that I can post and bug you with questions.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |