+1 to that. Using a Lee .45 compression plug in a powder through expander die for compression, works perfectly. About $16 for both.
Type: Posts; User: Flashman929
Forum: Black Powder Cartridge
+1 to that. Using a Lee .45 compression plug in a powder through expander die for compression, works perfectly. About $16 for both.
Forum: Black Powder Cartridge
Slip fitting won't work for me unfortunately, these rounds are mainly for hunting use.
I'm not getting any bullet distortion either, pulled bullets measure exactly the same as fresh ones, .460,...
Forum: Black Powder Cartridge
I tried it with thin airmail paper, and got no difference. Maybe it was too thin. I'll give the filter media a try!
Forum: Black Powder Cartridge
And I'm thinking that's it. The annealing is right on the edge of being too soft, and some cases it's just a bit too annealed.
Will poking the wad allow the air to escape from under the bullet...
Forum: Black Powder Cartridge
Michael, that was my thought exactly. .003 is .001 more than I use for j words and they take a fair whack to unseat with an inertia puller. It just doesn't make any sense they could have any play at...
Forum: Black Powder Cartridge
I'll try that Lumpy. Yes, a .030 card. Tried a thin paper card over the primer and between bullet and over powder card, but there was no noticeable difference so I discontinued. Compression is on a...
Forum: Black Powder Cartridge
Sorry, when I say "on the nose" I mean precisely. As in not .4565 or .4575, etc. It's. 457 all the way to the bell section.
I definitely found the Starline hard out of the bag, they annealed...
Forum: Black Powder Cartridge
Lumpy, I'm not tracking there brother... Measuring case wall thickness, x2, then subtracting from OD, and using pin gauges are the only two accurate methods of measurement. Using a case mouth dial...
Forum: Black Powder Cartridge
Well, I guess really it's both... I was working up a load to hunt with, and target shooting as a secondary use. So, you know, is a load that you can use for target shooting but mainly hunt with a...
Forum: Black Powder Cartridge
Here's a pulled one out of the melt box...
https://preview.ibb.co/nco5e5/20170821_211319.jpg
Forum: Black Powder Cartridge
I do, make sure there's no lube on the base before seating, those hollow bases sure like to pick it up.
Forum: Black Powder Cartridge
Thank you sirs...
I realized I omitted a lot of detail there... I'm using a Lee loader, all my presses and dies are 1000 miles away in my old province.
Neck ID was determined by measuring case...
Forum: Black Powder Cartridge
For sure. But the intent here isn't for target shooting, it's for moose shooting... So I need to know how it performs with no control. The answer appears to be good enough.
For target shooting,...
Forum: Black Powder Cartridge
Started with a wipe every shot, one damp, one dry.
Went down to a wipe every three shots.
Still have to make myself a blow tube.
It'd be nice to revisit on a day where I can be sure if...
Forum: Black Powder Cartridge
Welp, here I sit at the range, waiting a few minutes for the next shooters, figure they might like a go with the Sharps... er, Sharpses?
Loaded up another 100 of the 535 Postell last night. Didn't...
Forum: Black Powder Cartridge
This must surely have come up before, but I can't find anything that relates?
I'm loading the Lee 405 gr HB into Starline cases. Bullets mic at .460 just like they should. Case is .457 neck. 1/5...
Forum: Black Powder Cartridge
Good eye Bruce... I'm chalking it up to the angle of the backer; a piece of drywall at a 30 deg angle. We have some austere ranges here in NS.
Forum: Black Powder Cartridge
Nice BAW! Wow. Mine's only 3 into .73, it would have opened up for sure at 10 rounds. Just waiting for the pan lube to harden and I'll get some more loaded up to fine tune things tomorrow.
I had...
Forum: Cast Boolits
Huh. Well, first load I tried, 535 Postell over 70 grains Goex 2F did this, first three rounds at 100 yards getting sighted in. Seems to work ok.
https://preview.ibb.co/jeZqcQ/20170820_171748.jpg
Forum: Black Powder Cartridge
First outing today with my new Pedersoli Silhouette, topped with a 6x Malcolm.
Loaded up a bunch of test rounds with the Lyman 535 Postell, home made beeswax and olive oil lube, over 70 grains of...
Forum: Muzzleloading.
Necro post I know, but I was searching and it came up.
A soup ladle. Drill a 1/16" hole in the bottom. Scoop a bit out of your pot, and slide the mold under it. Works a treat, actually I'm torn...
Forum: Cast Boolits
For sure, that's the fun part! I've got a couple of molds en route, 2F and 3F at hand and a plan to try the different combinations of them to find out. Just waiting on primers too, all the other...
Forum: Our Chapel
This is a video made about my friends. Omer was my CO, a backwoods northern Canadian boy who grew up hunting and shooting, and one of the crustiest soldiers I ever met. If losing his RSM makes a guy...
Forum: Our Chapel
My friend, firstly, I'm sorry you had to go through that. I'm not a religious person, I just popped my head in to check out this forum and saw your post.
But...
I'm a (Canadian) army veteran,...
Forum: Cast Boolits
Thanks gents.
I googled up and down but didn't find anything answering this specific question. Obviously I'm 99% sure that fired brass will have clearance to not shave lead, but I've never...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |