Titan ReloadingReloading EverythingMidSouth Shooters SupplyRepackbox
Load DataInline FabricationWidenersPBcastco
Lee Precision RotoMetals2

Search:

Type: Posts; User: Yellowhouse

Page 1 of 10 1 2 3 4
Results 1 to 25 of 226

Search: Search took 0.02 seconds.

  1. Replies
    22
    Views
    740

    43 Spanish by Jameson has too thick rim for my...

    43 Spanish by Jameson has too thick rim for my Shiloh 44-77
  2. Replies
    7
    Views
    612

    Brass or steel receiver?

    Brass or steel receiver?
  3. If you think you need more horsepower use a paper...

    If you think you need more horsepower use a paper patch bullet seated out in the 50-70 That way you can stuff nearly 75 gr of powder in a modern case. I promise thats all you need. Secondly,...
  4. Replies
    38
    Views
    4,251

    It ain't rocket science! For ML use volume. For...

    It ain't rocket science! For ML use volume. For cartridge guns figure out the amount that fills the case to the base of the bullet, factor in your wad column and compression , if any. Then weight...
  5. Replies
    19
    Views
    3,106

    Don't waste ammo on male cowbirds! Take out the...

    Don't waste ammo on male cowbirds! Take out the females!
  6. Replies
    2
    Views
    123

    WTB One more time

    One more time
  7. Replies
    2
    Views
    123

    WTB Back up

    Back up
  8. Replies
    2
    Views
    123

    WTB WTB 44-70 or 44-90 CSS reloading dies

    Needing dies for either one of these straight cased offerings from C Sharps..
  9. Thread: Bison Hunt

    by Yellowhouse
    Replies
    22
    Views
    1,507

    Remington way back when put the hurt on the 40-70...

    Remington way back when put the hurt on the 40-70 as a bit light for Buffalo. All they had to do was up the bullet weight from 330 to 370. Worked for the 40-90/
  10. Replies
    93
    Views
    8,640

    Somewhere on a range up north they are going to...

    Somewhere on a range up north they are going to wonder why all those careless weeds (Amaranth) appeared after Val showed up to shoot.
  11. Replies
    18
    Views
    2,459

    I imagine 12.17 is the bore diameter. Europeans...

    I imagine 12.17 is the bore diameter. Europeans tend to measure their rifles that way....Americans began using groove diameter about 1873 or so .
  12. Replies
    12
    Views
    1,254

    I'm with Don......somebody went wild with a...

    I'm with Don......somebody went wild with a reamer.
  13. Replies
    102
    Views
    14,370

    What NoBade said.

    What NoBade said.
  14. Replies
    83
    Views
    9,541

    You could always dry brush the chamber to help in...

    You could always dry brush the chamber to help in loading another round. Speaking of, if you shoot wet I'd think you'd at least want to dry that chamber.
  15. Replies
    4
    Views
    1,029

    There are two types. On I the base fits into a...

    There are two types. On I the base fits into a long dovetail. On II the base is screwed to the top flat and no dovetail. Which is yours?
  16. Replies
    3
    Views
    945

    Dyna Tek Bore Coating

    Purported to slick barrels up and reduce leading/ copper fouling in needle blowers. I have a few SSR that aren't exactly pristine....salt and pepper pitting that are hard to clean sometimes after a...
  17. Replies
    26
    Views
    5,023

    Seems like John Boy did some testing on this very...

    Seems like John Boy did some testing on this very subject.
  18. Replies
    20
    Views
    5,167

    24 grains of that powder get you blackpowder...

    24 grains of that powder get you blackpowder velocities. 47 gr is in the realm of stout upper end Ruger #1 loads I'm thinking. Not even close to what Bodine used.
  19. Get the 40/70 SBN! It got a bad rep from...

    Get the 40/70 SBN! It got a bad rep from Remington as a buffalo killer despite a lot of peop using it. If it had more offerings using a heavier 370 gr bullet like its big brother then i suspect we...
  20. Replies
    29
    Views
    4,968

    Sorry you had a bad experience. Check your spam...

    Sorry you had a bad experience. Check your spam folders for messages. Anyway, John Walters is one of the best ive ever known....cant imagine whats happened
  21. Replies
    28
    Views
    4,438

    For those that wish for original rollers in...

    For those that wish for original rollers in 44-77. It just about has to be in the Sporting model. If its military its going to be something else. There are a few rare military trial types around...
  22. Replies
    23
    Views
    2,891

    In BPCR we use paper patch bullets patched to...

    In BPCR we use paper patch bullets patched to bore diameter. I was under the impression that for smokeless powder they were patched to groove.
  23. Replies
    28
    Views
    4,438

    Magnum or standard primer? Shootem and let the...

    Magnum or standard primer? Shootem and let the target tell you which one.
  24. Replies
    28
    Views
    4,438

    What Kootne said. 45ish is exactly what it...

    What Kootne said. 45ish is exactly what it should be for most originals. In those days before smokeless powder Remington referred to their calibers in terms of bore diameter and not groove. So...
  25. Replies
    3
    Views
    698

    WTT 280 Rem brass for 300 Savage

    Have 50 new 280 Rem brass by Hornady to trade for 50 new Hornady 300 Savage.
Results 1 to 25 of 226
Page 1 of 10 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check