Search:

What was the approx jacket length of the 600grain bullet? I'm guessing it's about 1.25".

Just got my 100 dollar prepaid Visa today from RCBS. Hopefully this gives hope to others that submitted the form for the rebate.

Some of this data is from websites that are no longer working. As always start low. It should give a good starting point for selecting powders.

219560

219561

219562

Enjoy.

For 357 Sig Nickel Cases, I used a 40SW Lee Carbide die to size the body. Then i used a Lee 357 Sig die to size the neck and bump the shoulder if needed. I did this without lube, and it worked...

I agree on the load data, if you PM me your email, I'll send you a few pages of load data I saved from another website a few years back. Most of my load data now is derived from using simular loads...

218790

I run these in my suppressed 12.5" 50 Beowulf. They feed amazing, and since they are the same profile, I just keep my dies the same and adjust the powder measure when I switch between...

218509

From left to right, 1000 grain cast, 690gr AP, 690gr Ball, and 150gr 308 in a 50 to 30 Sabot.

I used ~ 11 grains of A1680 to cycle my 8.3" 300 BLK and keep the rounds subsonic with the 230gr Lee TL boolit.

Thanks all for the information. This is an early version of the CSP-2. The following message came from Dave Corbin:

"You have an early version of the CSP-2 press, prior to the current changes in...

I'm looking for some help identifying what Corbin press this is. I figured it was a Corbin CSP-2, but the measurements don't match Corbin's site.

Corbin's site excerpts:
There is 15.5 inches...

Got this email today.

Dear dirtjumper895:

Congratulations! Your rebate for the Buy Green Get Green has been approved.

Please allow approximately 6 to 8 weeks to receive your reward.

If...

I run 50 Beowulf. I currently cast a 506 and 594 grain boolit and run them subsonic. I've also loaded 400gr Winchester Silver tops, 350 and 500gr xtp, and have some 325gr gold dot on my bench to...

I submitted $307 in items yesterday. A chargemaster and a set of dies. I did the rebate online, and expect to get 100 dollar rebate. I'll try and update this post when I get it.

Congrats fellas! Those were some good guesses.

I cant help a ton on 45/70 subsonic, however I run both 50 beowulf 594 gr and 510 Whisper 1000 grain cast bullets subsonic and suppressed. For both, I ended up running COWWs and powdercoating them...

2518 dirtjumper895

29 here, barely made it into the 20-30 group. I started reloading at 23, casting at 27 and have been enjoying it ever since.

add "money pit" to the list. Due to its great performance, i now have 8 different toolheads and a rt1500 trimmer, along with a Mr. Bullet Feeder to keep it fed.

I size .3565 for my Sig MPX ( slugs .3550), but size .358 for all of my other 9mm's. Id take the above advice and slug your barrel, or just size .358.

These are powder coated with Smokes Signal Blue. I size them to .502, and have a custom expander for them. I am currently in progress of getting the dies setup on my xl650 and loading these...

I shoot 506 and 594 grain plain base cast in my beowulf. I shoot it suppressed, and target about 1050fps. Still working on perfecting the loads, but it is looking promising. My gun is a 12.5" SBR and...

I purchased both .500 and .501 H&I dies, and tried both. I was able to get reliable chambering from the 0.501, and figured i can always use the .500 die one day if i need to for my other 50cals. With...

glockfan,

to read the dimensions on toms drawings, look at the arrows and numbers on the rightside drawing on his page. The dimensions with the up arrows are distance in inches from the base of...

So my current thoughts right now are to get dies to swage a 900-1000gr 10s tangent ogive rebated boat tail projectile. Thinking a 0.250" meplat, with a nose length of 1.5-1.7". And an overall...

A while back I got setup to nose size my projectiles, using a old Lyman 45 press. I had to make a shorter rod that pushes sizing die and bullet out of the die on the upstroke, and I am not running a...