Search:

Thanks for the comments, I'm sure I'm slowly lowering the temperature
Just as they say, it hardens faster that way

I started making some 9mm boolits, and I had the PID configured with 750F
I dipped one corner of the mold (aluminum) into the alloy
The mold heated up faster, actually cutting the sprue plate was...

I've done those types of loads in my FM with power pistol, really hot, I stopped at 7.4 grains.
I think your weapon is going to suffer accelerated wear if you use those loads a lot.
I have...

I have read your ideas, tomorrow I will go buy some cheap glue and if possible, one that works for high temperatures.
Thanks

Just as the title says, I have a Lee mold handle that the wood slides back, what do you use to fix them?

I do it with the ones I use for long range, I don't have a scientifically proven reason
I started doing it to improve the gas cut

Being optimistic, most of the time a 22LR does not shoot more than 100 meters. So in my opinion, you never need more than 4 or 6x if you are shooting casually and hunting.
Many of us would be fine...

I'll try 3031!

Thank you for your answers
We only have 3031, 4064 and 4350 available
The one that is really tempting me is 4350 for the 765x54 and 314299

Hello everyone, imr powder 4350, 4064 and 3031 have just arrived.
I have quite a bit of Win 760, do you think it's a good idea to buy a couple of pounds of 4350 to try on my 7.65x54 or my 308?...

thanks for answering
What I'm going to do will probably have to send the piece from France and wait in my friend's name at the hotel.
So it would only be passing through, and would not be purchased...

Does anyone know where I can get a tanfoglio/EAA stock 2 9mm extractor in Anchorage, Alaska?
A friend will pass by and can bring it to me, yesterday the one on my gun broke.
Thanks

Thank you all for the data, I think I will have to measure speed with this load to know where I am standing, although speed is not the best way to know the pressure, at least I have a parameter to...

Well, I have finally tried my new MP mold, https://www.mp-molds.com/product/359-640-solid-plain-base-no-lube-groove-8-cav-alu/
very good mold, it is not difficult to produce many boolits in a short...

I hope I don't hurt anyone's feelings with these words. I do not believe in any god nor profess any religion, although I have been educated in a Catholic school. Over the years, working as an...

More than 15 years ago, one afternoon I was in my range, and a man walked in, walking almost crouched, very old, with horn-rimmed glasses and green lenses. He came in with an old reusable grocery...

Thanks!




I need speed to go far, with the 311299 I can go up to 500 meters, I expected that with the TR 1:12 the 311466 would work better to reach 600 meters.
But it seems to me that I have...

A recipe that does not fail. This is for a steak that is at least one inch wide. First you wet it with water, then salt and pepper. Leave it in the refrigerator for a couple of hours.
Heat very...

I have had good results with 311466. This time they were boolits that I had stored with lubricant. I didn't measure speed, but obviously I should have given the other two much less.
Too bad I didn't...

zero leading

ok, I will try just pc



at the same time I shot other loads that were consistent



at the same time I shot other loads that were consistent

I was trying to get more precision for my long range shots with boolits on my cz 308. It has a TR of 1:12, so I loaded with winchester 760 49 grains behind the 311466 boolits, aluminum GC and PC and...

w231, cheap, measures accurately on the powder measure, it is always available, at least here in Argentina. I have no complaints.

In my country, a very good one is made in the military factory,...

Not only do you read good reviews and I see nice boolits
The weapons also look very nice
I was going to decide on the hammer, but I don't need hollow point, and I don't see that there is a mold...

Good afternoon, I was looking for the box for my 357 mag and I found that the manufacturer recommends using it with 125 grain bullets.
It's a taurus 605, I never really paid attention to it.
Does...