Nobade,
I am the one that asked. Thank you.
Sometimes function and form are the primary considerations. I do not think it looks that bad.
DougF
Type: Posts; User: kitsap
Forum: Single Shot Guns
Nobade,
I am the one that asked. Thank you.
Sometimes function and form are the primary considerations. I do not think it looks that bad.
DougF
Forum: Single Shot Guns
OK UncleBill,
Just about where is this range located ?
DougF
Forum: Single Shot Guns
Any chance you could share a couple of pictures, maybe before and after?
DougF
Forum: Casting Equipment
Small amounts of Kaowool insulation available here:
https://secure.anvilfire.com/
DougF
Forum: Casting Equipment
Make sure your TC is not touching the bottom or edges of your pot. Then fill your melter with alloy to about 3/4 full and look through your Auber controller instructions to start the auto tune...
Forum: Casting Equipment
Use your favorite search engine and put in home brew PID. The beer guys have been using PID's for some time with different types of heat sources including modulated valves.
DougF
Forum: Black Powder Cartridge
Here is a web site with a serial number look up option. The dealer will e-mail you the results.
http://www.trapdoors.com
The guy in charge is Keith Rush and he is trustworthy. There is a...
Forum: Black Powder Cartridge
You might be really surprised. Don't do anything dumb until you know the value. What is the serial number?? Such as 123XX.
Doug
Forum: Casting Equipment
Earthling121757, Zymurgy50,
The typical configuration for a dual voltage heating element is to have two segments with three connection points. The segments can be connected in series or parallel...
Forum: Casting Equipment
el34,
As you work through this issue I recommend you focus on that banana plug adapter as part of your problem and get it completely out of the circuit. The two terminals on the back of the PID...
Forum: Casting Equipment
el34,
Nicely done! The unit will provide you years of service.
DougF
Forum: Casting Equipment
el34,
No, never have had that much of a differential. I have built three using the Auber controller and Auber thermocouples. As part of the building process I would check the temperature with...
Forum: Casting Equipment
Silverbullit,
What you downloaded was the data sheet. Here is where you will find the manual such as it is.
http://www.instrumart.com/assets/TTMJ4manual.pdf
There is a set of menu options,...
Forum: Casting Equipment
Go to the upper right hand corner of the page and click on fast search for heater bands.
http://www.imscompany.com/Public/Home.aspx
DougF
Forum: Casting Equipment
I use a RCBS LAM-2 to size and lube 40 cal bullets for BPCR Silhouette. These bullets are 1.365 inches long and clear easily. I would estimate the maximum bullet length to approach 1.5 inches for...
Forum: Casting Equipment
A couple of pictures of what you have would be helpful. Also knowing the power draw (volts and amps) for the heating element would be necessary for any type of temperature controller.
DougF
Forum: Casting Equipment
bosterr,
Do you still have the Pb offset programmed into your controller? If you are using the short wire and comparing to ambient you should have Pb set to zero.
DougF
Forum: Casting Equipment
bosterr,
A couple of other things can introduce an error in temperature readings. One is the setting in the PID controller for the type of thermocouple you are using. Most likely you are using a...
Forum: Lead and Lead Alloys
Try here: http://castboolits.gunloads.com/showthread.php?147092-10-Amp-PID-Controllers-For-Sale-Customized-Available
DougF
Forum: Lead and Lead Alloys
Wrong forum.
Go here and start at the top with the sticky posts: http://castboolits.gunloads.com/forumdisplay.php?11-Casting-Equipment
Forum: Casting Equipment
For a general idea try this link: http://www.buffaloarms.com/Detail.aspx?PROD=162964&CAT=3902
The direct from the manufacturer prices may or may not be lower.
DougF
Forum: Casting Equipment
Some good information and ideas here...........
http://biggdawgtumblers.com/5601.html
DougF
Forum: Casting Equipment
I have cleaned a lot of black powder brass from BPCR Silhouette in an ultra sonic cleaner. There is a chemical reaction between the black powder residue and the Lemi-Shine. For black powder brass,...
Forum: Reloading Equipment
Some good information and ideas here...........
http://biggdawgtumblers.com/5601.html
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |