Search:

The CMP shipped all my cans and SPAM cans in boxes ground

I just bought a,CMMG upper and mags.
And have ammo cans and cans of Lyman/Ideal 358242 that are 128 grains and shoot well in my S&W 3rd gens and 1911s.
Are 100 % my go to range fun loads.
I have...

I cast 2000 or so and have gas checks.
I looked here over time and only see loads listed of 18 grains of H-335 That load was stated that it worked very well.
So that was the plan. But i waited...

I am using 4895 at 34 grains and Varget at 35 with a,200 grain cast gas checked 311365 and 311299.Cycles fine and shoots well.

Years ago I had a member of the CMP Forum Unclenick Get me some some loads on quick loads Thanks Nick
Take the info for what it is. The use of it is 100% at your own risk.
To get some base line...

I had one book that showed it at 75 grains but it was a misprint. so please disregard that post above
All the other Lyman books I think 1971 states 95-grains as does the picture.
But mine still...

I wanted a light 9mm for 9mm revolver loads I found the 356404 (now obsolete) for Unique Cream Puff Loads.
The 356404 was used in 9mm and 38 Super loads. So was a great candidate for 9mm Revolver...

Thanks
8-10 Bulleye sounds great I have checkes but lube everything with Larry's Red Carnuba Commercial.

The Garand is 100 percent with the 311365 as it is 200. I know guys shoot as low as 125 Jacketed in 30-06 Grands but thought 115 would be way low and I have the Loads down already with the 200's so...

I have 2 Rifes a 1903 and a Garand.
Presently I use a 311365 in both with 34 grains of 4895 or 35 of Varget
I found this new RCBS 30-115-SP in my stash.
So I figured it would be good for them....

I have some 311365 and was told to use the starting 220 loads for jacketed. it is 200 grains
I also have the RCBS 115 GC mold Maybe the same 125 Jacketed start loads
Thoughts?

My go to loads for one of my 1st molds is.
Lyman 358242 sized to .357 with 3.6 grains of Red Dot. Or 4.0 of WW231 Both at 1.160" OAL

Very much in there.
The HP holes takes away 20 or so grains. It is a large HP hole.
I also have one of Al's Gas Check Seaters I was thinking about seating the balls with. They have a disk that...

I bought some as I thought they were if nothing else cool.
As a side note: My wife and I only carry factory ammo and got a great deal on Nosler Target 9mm HP. As was my understanding is some slow...

I got one of Al 1st run of the old Lyman 311365 200 grain gas checked in brass. 34 grains of 4895 and 35 of Varget was also ,tested by my self and 5 or more others at the CMP Forum they shot well...

I load 34 Grains 4895 with gas checked 311365 and also 35 grains Varget in my Like New Garand so sized to .309"
These same loads were tested by Members of the CMP Forums.
I am using the same loads...

I have a pistol that was my moms. Startline Brass.
I have a RCBS 98 SWC
And Mihec 32 77 solid 63 HP have no cast with it yet but that is what it says
Published Loads I have are:
Cast 78 5...

I ended up getting a mint condition RCBS 98 grain one.
As I have never gotten a bad one from RCBS. and will on time send it off to Eric to get HP conversion done.
Gave 60 bucks won't be into it...

I have been looking for one. Was hoping NOE or Accurate had something I could just buy.
Maybe it is just me but would like a click and buy with a picture and the Accurate site is very hard for me to...

Does anyone make a 32-90cm in Hollow Point? or closer to 100 in 2 cavities or 4.

I looked at that one and a few more the site is so busy hard to even figure out how to order one. Not very user-friendly

Thanks. It is for a 1934a MAS. Moms gun.
I had some ammo that Quality Cartridge made from 32 S&W turned down brass into 7.65mm x20 {7.65 French Longue MAS}
But it was stolen
Starline now makes...

The alternative I am looking for is a 98-100 grain round nose.
The RCBS description says SWC but sure looks like a round nose mold made into a flat point.
Anyone have or use this mold?
I looked at...

In North Kenner. I am sure you see me post on Bayoushooter.
I know I see you. I try and see all lol.

I have this and was thinking of an NOE Crammer Style with more Cavities but looks like he has none in stock
https://www.bayoushooter.com/forums/attachment.php?attachmentid=86967&d=1527912409