That is Bill Ackermans shop. His daughter is doing the work now . I have had 2 Weaver T series scopes cleaned / tuned by her . Great service and reasonable service time . Barry
Type: Posts; User: bwgdog
Forum: Our Town
That is Bill Ackermans shop. His daughter is doing the work now . I have had 2 Weaver T series scopes cleaned / tuned by her . Great service and reasonable service time . Barry
Forum: Case Forming / Re-forming
Name of company making 32/40 is Load X in N. CA . hope this helps .
Forum: Our Town
Anybody had any contact with Ron at Octopus Solutions ? I have gotten calls from them . tia bwgdog
Forum: Military Rifles
Ted Brown Rifles in Oregon. Have had Ted do my gas gun work for the past thirty years without any problems. Barry
Thank You Al-Great turn around time on this mold being made---
Forum: Lead and Lead Alloys
If you are close to Sacramento I have isotope lead that you could use as is for handgun-I am in need of some soft for breech seated bullets. Welcome to the Forum!
Forum: Single Shot Guns
I am in Sacramento. I send my bolt gun work to GAP in Kansas-Send my gas gun work to Ted Brown in Oregon-Send my SS work to CPA in PA. You might check over on the SS forum as there are fellows that...
Eric hollow point-Has done a few for me-great work and turnaround.
Forum: Lead and Lead Alloys
Roto Metals-site sponser-top of page.
Forum: Cast Boolits
Swede- Any hope that in the future we could see some of the popular molds done in iron ? tia
Forum: Lead and Lead Alloys
Make sure you keep a lid on the pot-keeps heat in the pot-gets all the lead out of the jackets.
Forum: Cast Boolits
Would like to see Al-NOE-make both the 332/334 with correct specs the two molds I have are both out of spec.
Forum: Casting Equipment
PS-Could you tell us the name of the company that the molds are being outsourced to ? tia
Forum: CB Loads / Military Rifles
There is also the saga of the 7mm THOR from BC. If the remake is made-it might be a keeper. Time will tell.
Forum: Military Rifles
I have spoken to them at Criterion - are in development-would not hurt to call them and show interest-Also checked on importing some from AU but end cost for a GOOD new made barrel with all the fees...
Forum: Cast Boolits
I have same unit as Rick-It is a great piece of equipment.
Forum: Casting Equipment
Guardian-The first thing that I noticed when I received my Magma w/pid installed was the quality of the materials used. It works. Very well made unit.
Forum: Casting Equipment
Went with 120v and went with the installed PID-am VERY glad that I purchased it. Product is well made-with quality materials-and people that will answer questions if you have to phone them. Have had...
Forum: Casting Equipment
I bought two of the 2.5 lb four cavity molds from Brandon Foundry when he made the first batch for the CB Forum. Great molds + the ingots fit in small flat rate box for shipping. I only do 200 lbs at...
Dragon-That one is the ONLY mold -custom-that I have had real challenges with-But-the 3 cav hp-same bullet works fine???
Forum: Reloading Equipment
I have a Bench Source-Great unit-great cust service. Very happy with it.
Al does supply the oil-all you have to do is look at the page when you order your mold and clink on the box where it shows lube/or the other if you want set of allen wrenches with your mold. His...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |