I have an MP mold that casts 135 grains, I load them with 3.4 grains of WST and have no problems knocking over steel for all of my 3gun shooting, also nice in my PCC but not the sig mpx that is too...
Type: Posts; User: bzajdek
I have an MP mold that casts 135 grains, I load them with 3.4 grains of WST and have no problems knocking over steel for all of my 3gun shooting, also nice in my PCC but not the sig mpx that is too...
Forum: GB RUN BY Lakehouse2012
I would like a six cavity aluminum smooth side .453 please. Email bzajdek atttttt hotmailll dotttt commm
Forum: Group Buy Archives
Received mine on 7/30/19 as well, I am glad it arrived.
Forum: Group Buy Archives
Mine also shows June 18th as the last date it was recognized
2019-06-18 07:45 SILJUA, Departure from outward OE
I think it may have gone missing?
Forum: Group Buy Archives
bzajdek attt hotmail dottttt commm
SOLID- NO Lube Groove- .358- 8 Cavity PB-Aluminum mold
Forum: Group Buy Archives
If the order is not sent yet I would like a solid 311 5 cavity aluminum gas checked mold.
Bzajdek attttt Hotmail dotttt commm.
Forum: Group Buy Archives
If I can still get in I would like 2 identical molds
2X 8 cav aluminum 135 gr bevel base .357 diameter if it is not too late.
bzajdek atttt hotmail dotttt commmm
Forum: Group Buy Archives
I would like a 4 cavity hp gas check mold please
Bzajdek attttt hotmail dottttttttt commmm
Forum: Coatings and Alternatives
I have done a lot of do it spro jigs for saltwater fluke fishing. That is how I actually found this site while I was looking up alloy questions, then I began casting boolits shortly after that. ...
Forum: Group Buy Archives
Bluejay75
I do not see my order on the first page. I posted on post number 55, can this please be updated or is it too late.
Forum: Group Buy Archives
I would like an 8 cavity aluminum, NLG GC .227 mould
bzajdek atttt hotmailllll dottt commmmm (02893)
Forum: Group Buy Archives
I understand the group buy has been closed but if there is any room I would like a 4 cavity all pins .360 plain base, if not I understand.
bzajdek atttttt hotmaillllll dottttttt commmmmmm.
Forum: Group Buy Archives
I would like an 8 cavity aluminum .358 bevel base, no lube goove for hi tech coating.
bzajdek attttt hotmail dotttttt commm
Forum: Group Buy Archives
I would like one of these also 358 pb 8 cavity
bzajdek attttt hotmail dotttttt com
Thanks
Forum: Group Buy Archives
I would like a 2 cavity, gas check, hp all pins .311 please
Bzajdek attttt hotmail dotttttt com
Forum: Group Buy Archives
I would like a 6 cavity PB base 432 mold
bzajdek attt hotmail dotttt com
thanks
Forum: Group Buy Archives
Hello I would like a 4 cavity HP all pins
bzajdek at hotmail dot.... com
Thanks
Ben
Forum: Group Buy Archives
I would like an 8 cavity aluminum .358 smooth side for PC and hi tek
thanks
bzajdek at hot mail dot com
Forum: Group Buy Archives
Boolits look great, I would like to sign up for an 8 cavity, flat base, hi-tech for powder coating.
bzajdek at hotmail dot com.
Forum: Group Buy Archives
I. Will take one .678, bzajdek at hotmail dot com
Thanks
Forum: Casting Equipment
I was thinking holes may help with heat distribution but I was worried too much may lose some heat. I am not sure how much though? I also thought the flame might burn cleaner and deposit less...
Forum: Casting Equipment
Ok, so with the replies as of now it does not seem necessary, nor would it provide any benefit. I was just trying to get opinions before welding the ring as it would be much easier to perform the...
Forum: Casting Equipment
Before I weld the ring to the bottom of the pot should I drill or cut vent holes to get better flame or heat to the bottom of the pot?
Forum: Group Buy Archives
I would like a 147 flat base no lube grove, 6 cavity aluminum. Thanks
bzajdek at hotmail dot com
Forum: Reloading Equipment
Ok so probably the lowest speed, I think trimming brass with the worlds finest trimmer WFT they recommend a fast rpm but these are two different types of operations.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |