Search:

I see this thread is almost a year old but I just purchased this mold from a member here, so I'm going down this road now. I'm wanting to load this for for my S&W M&P shield 9mm. Did you stick with...

I have never used it but have some on the way to try with 40 S&W. I have seen a number of favorable reviews for it.

Thanks for the good ideas JBinMN!

In doing some cleaning out I found an unopened pound of each of 231, Bullseye and Red Dot powders I purchased in the 80's. I also have a Speer 1988 Reloading Manual. In comparing some data from the...

If that is a 6", I have the same gun I bought new in about 1990. Too bad I didn't invest my 401k money in a boatload of these instead of mutual funds!

Thanks guys, this is an awesome forum, so many helpful people here!

This one Rattlesnake Charlie and flashhole?

https://www.titanreloading.com/40-sw10mm-auto-taper-crimp-die-?search=taper%20crimp

I'm about to start reloading 40 S&W and would like suggestions on crimping. I have not had good luck with the Lee FCD for handgun rounds. I just purchased the Lee Deluxe die set here because it was...

I just purchased an older Interarms Rossi .38/.357, 20" model 92 SRC from a member here just a few days ago. It is a very nice gun but I have not had a chance to shoot it yet.

Thanks for this info! I'll have to keep that in mind as I try different loads.

I just purchased the Rossi .38/.357, 20" model 92 SRC that Texas by God was speaking of in the post above. It is a very nice gun! Very nice people too, thanks Thomas!

Thanks to everyone for all this great information!

I'm on the group buy list for the MiHec Aluminum 8 Cavity 358429 Keith SWC. I'm hoping this will pair well with whichever of these I end up with.

I have been wanting a lever action 357 for sometime now and I'm finally ready to pull the trigger! I'm looking at guns in the lower end of the price range mainly because I don't want to spend a bunch...

I use Berryman B-12 Chemtool in my gas tank as a fuel injector cleaner about every other month. I buy it in the 15 oz. cans (non-aerosol) and I always have a few empty cans on hand because they are...

Very good point.

I went ahead and purchased the HP-38 yesterday, so I am going to still be on the lookout for something better for 357 Mag loads. I talked to a guy that worked there and he said two weeks ago they...

I am at cabelas now. The only thing they have from all the powders listed above is 4227 they just put out HP-38 any comments on that?

Thanks for all the info. I am about to go do my shopping and see what they have. After reading all this, it dawned on me that this is a similar response that you would get if you asked a bunch of...

Haha, amazing huh? It is hit and miss as to what they will have, that is why I wanted to get several ideas. I guess after thinking about this a little more, I should have the 38 Special covered with...

I am going to be in Cabela's tomorrow and was going to pick up some powder. I am reloading 38 Special and 357 Magnum and have ordered the Lee 358-140-SWC & C358-158 SWC molds. What powders are good...

They are lubed, I just cleaned it off this one for the picture. Thanks for the info!

I found a box of these I forgot I had that I bought years ago at a gun show. Is it a standard design from a commercially available mold? It is sized to .358 weighs 153 gr and is .672 OAL.

...

For a cheap solution to forgetting to turn off the case tumbler, buy one of the very cheap mechanical timers used to turn lights on and off. Open the device up and determine how the power is...