S@W Pre. M10

Here is the picture of it.Attachment 228039 The son bought a new gun sold this to me. Best I can figure it was mfg. in the '30' sn 308xxx

Yup! .38 Special Hand Ejector.

DON'T shoot any +P in it, standard lead loads only.

I am to old to shoot + P :-P

I +P at night. I'm old too.

Sent from my SAMSUNG-SM-G930A using Tapatalk

Nice gun; DO WANT! But have something else I can shoot, at least.

They are wonderful smooth and accurate vintage revolvers. I had man a dozen or more over the years and still have two of them. Everybody is correct that you will beat them to pieces in short order with higher than normal pressure.

I take it down one step more and load all my plinking and range 38 Specials with 3/Bullseye over your prefered 150 - 160 grain cast bullet. This is below the full snort level and are just as much fun to shoot.

Here are my remaing two a 1913 and 1931 production.

Very nice. Not many things made today with such attention to detail.... At least not that I can afford ;-)
Greg in West Mitten

Heck common as house flies! Everybody's got one:-)

S-prefix about 1945.

Attachment 228130
Attachment 228131

Quote:

---

Originally Posted by Dutchman

Heck common as house flies! Everybody's got one:-)

S-prefix about 1945.

Attachment 228130
Attachment 228131

---

At the gun shows around here something that nice would go for $900-1000. A rusty piece of junk they'd ask $400+ and the seller would more than likely get it, but, not from me.

OK, gotta join the party here and post some eye candy:

Attachment 228134Attachment 228135

Quote:

---

Originally Posted by Char-Gar

They are wonderful smooth and accurate vintage revolvers. I had man a dozen or more over the years and still have two of them. Everybody is correct that you will beat them to pieces in short order with higher than normal pressure.

I take it down one step more and load all my plinking and range 38 Specials with 3/Bullseye over your prefered 150 - 160 grain cast bullet. This is below the full snort level and are just as much fun to shoot.

Here are my remaing two a 1913 and 1931 production.

---

There is a problem I have when I check these threads; it gets me to thinking. Just wondering if your pre-10's shoot to point of aim with 3 grains of Bullseye and a 160 grain SWC. And then I was thinking about my old war horse Victory, and how I might just see how it shoots with that load.
Attachment 228142

It gets me drooling since I don't have one, or an M10, sigh. Youse folks are definitely enablers LOL

Of course like a lot of us here I didn't buy a box full of PD trade ins when they were $125 each 20 yrs ago. Of course I wish I did. The Original M&P is my 2nd favorite S&W revolver behind the Combat Masterpiece. If I was limited to one handgun, the m10 4" would suit fine.

Sent from my SAMSUNG-SM-G930A using Tapatalk

Quote:

---

Originally Posted by JoeJames

There is a problem I have when I check these threads; it gets me to thinking. Just wondering if your pre-10's shoot to point of aim with 3 grains of Bullseye and a 160 grain SWC. And then I was thinking about my old war horse Victory, and how I might just see how it shoots with that load.
Attachment 228142

---

Bear in mind these old pistols were sighted for a "center hold" and not the 6 O'Clock target hold we are used to. Also with the old hump back hammer you can't see the rear sight with the hammer down.

Quote:

---

Originally Posted by Char-Gar

Bear in mind these old pistols were sighted for a "center hold" and not the 6 O'Clock target hold we are used to. Also with the old hump back hammer you can't see the rear sight with the hammer down.

---

Exactly, that is why I designed this target; a variation on the Brit tin hat target:

Attachment 228165