Unless you intend to shoot black powder loads, I have to disagree regarding Micro Groove rifling being undesireable. Micro Groove with proper bullet fit shoots as well as any other rifling pattern.Quote:
Originally Posted by FergusonTO35
Is an 86 a better rifle? Sure is a lot heavier = less painful recoil but lots more to tote. Much more complicated rifle.
Regarding price, if you want such a rifle, the price is on the top end of the going price in my area.
My micro groove rifles shoot boolits just fine. I guess what I meant was, that MG *might* require a different approach than standard rifling if the OP had no experience with it.
FWIW, Mine is not "micro grooved" it has the older "Ballard" style rifling and Years ago I "smoothed-up"
the action sufficiently that I can Feed FIRED cases from the Magazine tube and into the chamber than
Out as fast as my hands can work the lever!
I have not tried the Hornady "tipped ammo" in the rifle, but I'd be shocked if it didn't feed at least as well as FIRED cases...
Yup, just like mine. Great rifles!
After a little snooping I learned that the first ones built in the seventies had "BO" starting the serial number . Also the I'm told the first ones had Douglass barrels and I think it was six groove rifling . I watched one sell on Gunbroker a couple years ago in like new condition for over nine hundred dollars .
Glad you got one you like Jmort , they are a blast to play with .
Jack
I bought one 2 years ago, in .44mag. Its a nice rifle but the safety is disgusting so I bought one of the safety deletes with the saddle ring and now it looks ******. It also shoots great. it was manufactured in 2011.
Yup that is what mine sold for on this site (shipped ) as I remember /EdQuote:
Originally Posted by jmort
FWIW mine is marked with the JM (in an oval) on the left side of the barrel with about a quarter if an inch spacing between the Receiver and the edge of the stampingQuote:
Originally Posted by azrednek
THX Allan, I couldn't find it because it's not there.Quote:
Originally Posted by AllanD
I have one in 45-70 and it cuts 1/2 groups at 100 yards with both 300 + 350gr Hornadys.With 4x Leupold.Never got around to trying cast yet.
IF i were you, i'd bite the bullet and buy it, if, its in that kind of condition. I bought a 1998 model 45/70 in what i thought to be very very good condition. It was, i did the safety delete and, i'm very happy with it. If you don't tell anyone, they'll never know. I do not say it is some thing it is not. Meaning its not a early pre safety. But, i'm tickled to death to have it. I'd like to find a nice pre saftey 44 mag in some thing i could just use to carry out in the brush, when just out looking around.
By the way, i don't think the price is out of line,maybe you can offer a little bit less, but, if you want it, don't let it get away from you. Or, you'll be posting about ''the one i didn't buy'' type thing. lol
If it's a bastard acme thread or a square thread it will have to be done on a lathe. No such tap will be likely available for the acme if it isn't a standard pitch and I don't think I even heard of a square thread tap. If your thinking of running a tap to thread a receiver or use a die to cut threads on the barrel, you might just consider having your local gunsmith do the work for you. It will be much cheaper and the end result will be much more satisfying. Just my opinion, others will differ. Good luckQuote:
Originally Posted by modified5
Good decision, I have one made in 1974, micro groove rifling and all. It’s killed several deer, feral hogs, even a heart shot on a bobcat at 135 yards. I sure wouldn’t sell mine for $800.Quote:
Originally Posted by jmort