Yes, if there was enough interest in a NLG design, the BB could be part of it, but then that cherry would never be useable for a grooved mold.Quote:
Originally Posted by kevin c
Sent from my SM-A102U using Tapatalk
Printable View
Yes, if there was enough interest in a NLG design, the BB could be part of it, but then that cherry would never be useable for a grooved mold.Quote:
Originally Posted by kevin c
Sent from my SM-A102U using Tapatalk
I genuinely hate to do this, but please remove me from the list. The timing of this closing could not have been worse, started the new year off with over $2k in medical bills for my 6mo old (some surgeries, he's doing well though).
Hopefully I can pick up an overrun late in the year or I'll have to catch it next time. Thanks.
12) (drfroglegs) - 8 cav Al, NLG, FB - drfroglegs at yahoo dot com
Hi Frog,
I'm sorry to hear of your boys' issues, and good to hear he is doing well. Family takes priority to toys, every day!
I've removed you from the list, but because Miha has already closed it, you may have to tell Miha when the invoices come out of your situation. Hopefully he sees this any doesnt even send the invoice.
Speedy recovery for your son.
Quote:
Originally Posted by drfroglegs
just wondering about how long it usually takes Miha to get in touch after a group buy closes. Asking because this is my first time and I do not want to mess the up.
I'm in this GB for a NLG 6 cavity. I already have the 6 cavity lube groove mold but haven't loaded it yet. I now have two grandsons(grown) that have 9mm pistols. Can anyone point me to a thread that has proven loads for this boolit, both conventional lube and PC? I'm hoping that I can find time to develop some loads for their guns that allow them to get in a lot of practice. The same applies to me. I've got a couple of 9mm's myself and would like to shoot them more.
All I've loaded so far is some PC boolits that I purchased from a commercial caster that operates down the road from me. He apparently got into it to support his competition habit. I prefer not to deal with him. I think he recommends whatever he has an excess of at the time.
I’ve had pretty good luck with both wsf and Alliant sport pistol with this bullet hi tech coated around 3.5 grains of either is a good starting point 4.1is where I ended up with wsf and 3.7 sport pistol.Quote:
Originally Posted by alamogunr
Never heard of these powders so I had to look it up. From manufacturer's partial description: ...Sport Pistol's low-muzzle-flash formulation is also optimized for polymer-coated bullets, whereas comparable powders can dissolve polymer coatings at the bullet base during ignition.
Who knew that manufacturers starting to pay attention to us powder coaters :)
I have been using this powder for about 6 months. Meters really well. I like it.
Lakehouse2012,
Do you have any idea what the status is currently with our here group buy?
It is just so quiet at this point in time.......
I don't have either of these powders at present. I do have lots of Bullseye, Red Dot(& Promo). I can't find any loads using boolits in this weight range and Red Dot. Bullseye yes. Don't really understand why Bullseye but not Red Dot. I'll probably stick with Bullseye since I'll be loading for my grandsons. Don't want to take a chance with a non-load manual load for them.Quote:
Originally Posted by Papercidal
Hi guys,Quote:
Originally Posted by hermans
Miha has this one on his short list, he is starting to get cherries in and was going to be cutting blocks this week. I'd guess that we get emails in next few weeks.
Sent from my SM-A102U using Tapatalk
http://www.alliantpowder.com/reloade...2&cartridge=23
They have 145 and 124 grain cast coated listed. Start with the heavier data and work up to mid way which would be 3.7.
Any info on this? I'm paranoid that he'll send the email out and I'll lose it in the mix.Quote:
Originally Posted by Lakehouse2012
Not yet but should be in the next week or two.
What Lyman top punch # to lube this boolit??? Or can we order one withour order? afish4570
Miha includes a top punch
2 days ago I ruined my mold from the last run any chance there is going to be an extra 8 CAV BB/NLG?
I'm certain there will be Loudy13. Keep an eye out on this thread for when Miha starts shipping and then write him a PM. He always has extras.Quote:
Originally Posted by Loudy13
any word on this one? I have him holding my 300 BO mold so I can have them ship together.
will doQuote:
Originally Posted by Lakehouse2012