MiHec 2 or 4 cavity brass 358640 380 ACP/ 9mm Luger & Makarov Cramer HPGC or PB

Quote:

---

Originally Posted by Ruger480

2 cavity brass 358640 380 ACP HP please.

---

I need the base type you want... either plain base or gas check and which HP.... either large or penta you want.

Thread updated..............

Sorry, plain base and Lg HP.
Thank you,
John

OK, I'll play. .358 plain base four cavity with large and penta pins.
buzz at joniypc dot com

I could also some advise. Planning on using for a PPK. Probably wouldn't load the round too hot. Would I need the gas check and which hollow point option would work better? Thanks

Quote:

---

Originally Posted by dogman

I could also some advise. Planning on using for a PPK. Probably wouldn't load the round too hot. Would I need the gas check and which hollow point option would work better? Thanks

---

380s are notorious for not expanding jacketed HPs. You have to have a top end load with jacketed to get satisfactory results. With cast.... cast the large HP with 25 or 30:1 lead/tin and push it to top book loads. The GC will help you on that.

I'd like a four cavity w/GC .358 with large pins

mlmaher at gmail dot com

Can I change mine to a GC version please.

I'll take one 4C 0.358 PB Large HP and solid pin
magnut44 at gmail

Hi 45 2.1

Looks like you are at (over) the 15 takers - this should go in pretty quickly now. Can't wait to try out a MiHec!

I'd like to sign up for 1 .358 plain base 2 cavity mold with penta hp pins. Thanks
Apexservicesomaha att g mail dott com

Quote:

---

Originally Posted by 44 mag nut

I'll take one 4C PB Large HP and solid pin
magnut44 at gmail dot com

---

What size? 0.358" or 0.366".............

Quote:

---

Originally Posted by Buzz64

Hi 45 2.1 Looks like you are at (over) the 15 takers - this should go in pretty quickly now. Can't wait to try out a MiHec!

---

There are quite a few GBs in front of this one..... it will be a while yet.

Thread updated..............

4cavity pb mould all pins LUP rstaab (at) Panix dot com

.358 diameter

Here we go again..... Two cavity PB .358 Lg pins w/extra set of Lg pins

darkh2odiver (at) hotmail [dot] {com}

Thank you.

45 2.1,

Put me down for one 2 cavity 0.358" plain base mold with large HP pins...USSR.....ussr at empacc dot net. Thanks.

Don

Quote:

---

Originally Posted by lup

4cavity pb mould all pins

---

What diameter? .... 0.358" or 0.366"

Thread updated..................

Edited. .358 diameter. I'm a dope.

Bump, and a quick question for 45 2.1: It was stated that 15 commitments to buy were needed for this group buy to come to fruition. We have 22 commitments at this point. Is there a certain number of commitments or a certain date at which point the group buy will be closed and proceed on to the creation of the moulds? Thanks.

Don

I'm with you USSR, seems like it should be "last call" time.

Quote:

---

Originally Posted by USSR

Bump, and a quick question for 45 2.1: It was stated that 15 commitments to buy were needed for this group buy to come to fruition. We have 22 commitments at this point. Is there a certain number of commitments or a certain date at which point the group buy will be closed and proceed on to the creation of the moulds? Don

---

Quote:

---

Originally Posted by Buzz64

I'm with you USSR, seems like it should be "last call" time.

---

There is no "last call time" on any of the GBs I run. To be viable to have a run, the minimum number is 15 molds, but that doesn't mean that the GB will close and be ran at that time either. MiHec controls when a GB will close and when he makes it......... I do not.

Thanks for letting us know, 45 2.1.

Don