CLOSED - MP .227 -65 GN GC/ PB 6 Cavity Brass or 8 Cavity Aluminum 223/ 5.56 Nato

I'd be in for this one as well.

8 cavity plain base. No lube grooves. rocpyro at gmail. 76116, handles.

37031

I think I'll pick up a second mold, this time with PB

(royboy216) (rlapid216 at gmail dot com) .227-8 cavity-PB-No Lube Grooves- 80222

Quote:

---

Originally Posted by gvanzeggelaar

Could I get the lube grooves removed from my mold.

Thanks

---

Good Day. Could this be updated. Sorry for inconvenience

Fixed up Royboy

Uh, actually the second mold should be plain base.


Sent from my iPhone using Tapatalk

Done.

Thank you!


Sent from my iPhone using Tapatalk

ok dumb question. Would the NLG with gas check, work like boat tail, without actualy putting a GC on it? most plain base give me a little burr when I drop them, probably due to my range lead mix. I'll switch to lino or close to it. plan on powder coating, but would like to eliminate the step and expense of GC'ing.

The picture on the front didn't particularly say that it was the GC with grooves, but its implied.

Quote:

---

Originally Posted by Master Samwise

ok dumb question. Would the NLG with gas check, work like boat tail, without actualy putting a GC on it? most plain base give me a little burr when I drop them, probably due to my range lead mix. I'll switch to lino or close to it. plan on powder coating, but would like to eliminate the step and expense of GC'ing.

The picture on the front didn't particularly say that it was the GC with grooves, but its implied.

---

I am by no means an expert in anything and I think lube grooved boolit seems to obturate better and are less finicky to find a good load.

It could serve as a rebated type boat tail.

Bluejay75

Is this group buy still open?
If so I would like to get in pauldotadotshoemaker1atgmaildotcom. .227-8 cavity-GC-No Lube Grooves. zip 28326

Quote:

---

Originally Posted by Smk SHoe

Is this group buy still open?
If so I would like to get in pauldotadotshoemaker1atgmaildotcom. .227-8 cavity-GC-No Lube Grooves. zip 28326

---

I’m in Sanford right now. Will get you fixed up when I get home.

Guessing by the corp patch and oak leaf you are doing a little messing around on Bragg.

I've changed my mind on the second mold, 8-cav aluminum mold (#5 on the list, vfluckey at midco dot net)

I want to change it from NLG-GS to a lube groove-PB (still 8-cav AL)

and add DHL shipping to my order.

thanks!

I'm debating getting a 2nd identical set of mold/handles, hoping our Honcho gives us a day's notice or two to make our silly minds up just before going into launching mode :)

All taken care of Gents!!!

Quote:

---

Originally Posted by Mr_Sheesh

I'm debating getting a 2nd identical set of mold/handles, hoping our Honcho gives us a day's notice or two to make our silly minds up just before going into launching mode :)

---

If you know you are going for volume...get 2. You can get 223 brass by the bucketfull and have at it.

Bluejay please change my order to GC from PB. pjames32 at live dot com
Thx, Paul

Quote:

---

Originally Posted by pjames32

Bluejay please change my order to GC from PB. pjames32 at live dot com
Thx, Paul

---

Done. Did you change so it sits in the case better while loading or do you plan on GCing the boolits?

8 cav gc with lube groove please
readr1 yahoo

I plan to GC the boolits. From what I've been reading I will need to move them faster to cycle an AR. Input appreciated!