Lather rinse repeat.
Printable View
Lather rinse repeat.
Maybe not this exact tool but something similar might help. I've got one bc of a bad knee.
https://www.amazon.com/Folding-Helpi.../dp/B0002VUQPG
Sent from my iPhone using Tapatalk
:) Yep,got me one of those"pickup sticks"works really well.Can even pick up a piece of paper with mine.Got mine at the local pharmacy,was $19.95 but is of good quality.Oh yeah,for getting up off the floor,you could always hang a block and tackle from the ceiling:roll:.
Good luck.Have fun.Be safe.
Leo
Magnets on a stick work for primers too.
I have those garage cushions that interlock, unfortunately I didn't have one in that space, but I should add more. I don't mind being on the floor sometimes, it's just the decision to stand up that complicates things. Block and tackle affair sounds like the best answer....
Yeah...for me though...when I get a package of primers out, I say out loud (so I'll pay attention)..."Hey Dummie...these are primers, you know, like 'Mexican Jumping Bean' kinda primers...pay attention!"
Still though, I'll have a few escapees from time to time!
Just finished resizing a bunch of 9mm brass. Sorted the commercial from the military and starting to swage prime pockets. Just put a load in the tumbler. Trying to do a bunch of tumbling this summer to utilize the hot summer sun for drying.
Last week my usual load of 18gr of 2400 behind a 160 gr boolits wouldn't shoot worth a damm 3 inch at 100 yards instead of 1.5 inches .so I've sized trimmed etc loaded up 20 rounds with 17/17.5/18/18.5/19 gr of 2400 I hope one of them will get back to shooting as it was .now to clean the barrel ,hope this solves the problem.
Resized another 200 or so pieces of 308 brass. Still have a gallon and a half to go.
And then I have to ream, uniform, and trim them.
I'm done buying once fired military 308 brass. I swear! :grin:
Loaded 250 12 gauge shells with home-made shot
What fun, what fun
Mike
Loaded and shot the 58 ML with 100 grans of powder under a 500 gr minie, big push on my shoulder, I likie a lot.
Also my 12ga ML, used the shot I made. This is fun to shoot shot I make.
I had to try out my new NOE 460-405 mold. Cast about 200. They were about 390 gr, water dropped, bhn 15. Plan on driving them about 1400-1500 in Marlin .
LGS has a Taylor n Co 45-70, 32 in barrel. Can't swing the 1200 bucks. Maybe if it's there next month?
Finished and installed another shelf unit to store coated bullets on
http://i.imgur.com/YvMNsGG.jpg
Cast 90 x190g x 358 sil boolits & 90 x150gr x 309fn boolits .lubed sized gas checked relubed .would have been more but my wrists started to give me some stick so I had to call it a day .club is shut next week so its time to stock up .
Loaded 100 158gr. RNFPs in .38 Special cases over 3gr. Bullseye.......................................... yesterday
Didn't do any reloading but did empty a couple of boxes of 9mm and 45acp that I cast and reloaded
[emoji6]
I processed some bees wax and pine tar
prepping some 303 brit brass for snake shot loads
Thanks, soundguy, guess yesterday was my day, got the shelf finished and installed then my neighbor called and asked if I wanted a reloading press he found. [He breaks into houses for a living (works for the mortgage companies maintaining and cleaning forclosed properties). A couple drops of KROIL and it 's smooth as butter.
http://i.imgur.com/iBTQsoe.jpg
http://i.imgur.com/CDKrbqM.jpg
http://i.imgur.com/7gI357o.jpg